Farm Perimeter Fence for Smallholdings | Techno Kol Uzi

t300-7

A good farm perimeter fence keeps livestock in, predators and intruders out, and holds up to weather and animal pressure over many years. For most smallholdings, a combination of sturdy iron posts and mesh or bar infill, finished with galvanizing or powder coating, offers the best balance of strength and durability. Techno Kol Uzi builds these fences to measure after an on-site survey of your land.

Why smallholders need a dedicated perimeter fence

A perimeter fence does more than mark your boundary. It protects livestock from wandering onto roads, keeps neighbors' animals out of your paddocks, and reduces the risk of dogs or other animals getting in at night. On a smallholding, a well-planned fence also makes daily work easier, because animals can be moved between sections without constant supervision.

Before choosing materials, think about what you are keeping in and what you are keeping out. Goats, sheep, cattle and horses each push and test fences differently.

Choosing materials for the perimeter

Iron fences are strong, rigid and well suited to heavy livestock and long runs. Aluminum is lighter, does not rust, and works well where a cleaner look or lower maintenance is important. Many smallholders combine the two, using iron posts for stability and corners, with lighter infill where appropriate.

Iron posts with a galvanized finish for long-term strength
Mesh or bar infill sized for the animals you keep
Aluminum sections where low weight and corrosion resistance matter

Planning the layout and gates

Walk the perimeter first and note slopes, drainage paths, existing trees and the location of access roads. Corners, gate posts and changes in direction carry the most load and should be heavier. Plan gates at points you will use daily, such as near the barn or the water source, and make sure they swing clear of the ground and any obstacles.

Sketch the layout with approximate lengths. This makes the later measurement and quoting process far more accurate.

Height, spacing and animal safety

Fence height and spacing depend on the species, so there is no single answer that fits every farm. The gaps between bars or mesh openings should be small enough that young animals cannot push through or get their heads trapped. Smooth surfaces and well-finished welds protect animals from cuts and snagged coats.

For railing-style elements, the Israeli standard SI 1142 is a useful reference. Exact dimensional values should always be confirmed with your engineer or our team during the site visit.

The on-site measurement and approval process

Our process starts with an inquiry where you send photos of the area and a rough description of your needs. We then measure on site, confirm ground conditions and gate positions, and prepare a written drawing and specification. You review and approve the plan before anything goes into production.

Once approved, the sections are made in our Tel Aviv factory, finished with hot-dip galvanizing or powder coating as needed, and installed at your property.

Maintenance to keep the fence working

Even a strong fence needs occasional attention. Check post bases after heavy rain, look for loose fixings or damaged infill, and touch up any scratched coating before rust can start. Keep vegetation trimmed so it does not press against the fence or hide weak spots. Regular checks are far cheaper than repairs after an animal has already escaped.

Frequently asked questions

What height should a farm perimeter fence be?

The right height depends on the animals you keep and whether predators are a concern. We confirm the best height for your livestock during the on-site visit.

Is iron or aluminum better for a livestock fence?

Iron offers greater strength for heavy animals and long runs, while aluminum is lighter and does not rust. Many smallholders use a mix of both depending on each section.

Do you install the fence as well as manufacture it?

Yes, we manufacture to measure in our Tel Aviv factory and handle installation at your property after you approve the drawing and specification.

How do I start a project with Techno Kol Uzi?

Send us photos of your land and a short description of your animals and needs. We will then arrange an on-site measurement and prepare a written plan for your approval.

Common mistakes to avoid

Many farms choose the wrong gap size or skip strengthening corners and gate posts, which leads to sagging, escapes and early failure. Ignoring drainage and ground conditions can also cause posts to shift over time.

Our recommendation

Invest the most in corner posts, gate posts and high-load points, and choose a galvanized or powder-coated finish for any iron work exposed to weather. Confirm the mesh or bar spacing against the youngest animals you keep before ordering.

Summary

A well-built farm perimeter fence protects your livestock, your land and your time. Iron and aluminum fences made to measure, after a proper site survey, give smallholders a durable solution that suits their animals and terrain.

השאירו פרטים ונחזור אליכם