Book a Site Visit for Aluminum Door Replacement in an Existing Frame

t414-41

To replace an aluminum door in an existing frame, you book an on-site visit where a technician checks the frame's condition, measures the opening and confirms whether the current frame can be reused. You receive a drawing and written specification before anything is manufactured.

Why a site visit comes before anything else

A door is only as good as the frame it sits in. Walls can be out of square, frames can have hidden rust, and old openings are often not exactly the size the drawings show. A site visit lets a technician see these conditions before a door is built, so the new door fits the real opening rather than the one you remember.

Booking the visit early also saves time. The measurements taken on site become the basis for the drawing and the specification you approve, so the door is made once and installed without surprises.

What the technician checks in your current frame

During the visit the technician looks at the frame as a structure. The key points are listed below.

Condition of the frame profile, including corrosion, cracks or loose corners
Whether the frame is level, plumb and square in the opening
Wall material and how the frame is fixed to it
Clearance on the hinge side, lock side and threshold
Swing direction and how the door opens into or out of the space

If the frame is sound, it can often be kept. If not, the technician will say so clearly and explain the options.

Reusing the frame or replacing it

Keeping the existing frame saves work and disruption, but only when it is in good shape. A frame with light surface wear and a straight, stable opening is usually a good candidate. A frame with deep corrosion, movement in the wall or a damaged threshold is better replaced along with the door.

The technician will advise whether the new aluminum or iron door can be fitted to the current frame, and whether a small adjustment such as a new threshold or reinforced hinge points is needed. Any structural decision is confirmed with your engineer where required.

What you receive after the visit

After the measurements are complete, you receive a drawing showing the opening, the door size and the position of hinges and locks. A written specification follows, covering the material, profile type, finish and the way the door is fixed to the frame.

Nothing is produced until you have reviewed and approved both documents. This gives you a clear record of what was agreed and a chance to ask questions before the door goes into the factory.

How the visit and production work together

The usual sequence is inquiry with photos, on-site measurement, drawing and specification, your approval, production in the factory, finishing and installation. Iron doors can be hot-dip galvanized and powder coated for outdoor exposure, while aluminum doors suit lighter-use entrances and are finished to match your existing windows.

Your technician can explain which finish suits your building, your exposure to weather and the look you want. These choices are made during the visit so that production starts with complete information.

How to prepare for the visit

A little preparation makes the visit faster. Clear the area around the door so the technician can reach the frame, and have the keys and any existing hardware available. Photos of the door, the frame and the surrounding wall help as well, and send them ahead when you book so the technician knows what to expect.

Note any problems you have noticed, such as drafts, sticking or water entry. These details help the technician find the cause and design the new door to solve it.

Frequently asked questions

Can I keep my old aluminum frame when I replace the door?

Often yes, if the frame is straight, stable and free from serious corrosion. The technician will check the frame during the visit and tell you clearly whether it can be reused.

Do I have to pay for the site visit before production starts?

Please ask the team directly when you book, as the arrangements for the visit are confirmed at that stage. Nothing is manufactured until you have approved the drawing and specification.

How long after the visit does the door get made?

Production begins only after you approve the drawing and written specification. The team will confirm the schedule once the approved details are in place.

Can an iron door be fitted to an aluminum frame?

This depends on the weight of the door, the frame strength and how it is fixed to the wall. The technician will assess this during the visit and recommend the safest option.

Common mistakes to avoid

Many owners order a door based on the old measurements without checking the frame, which leads to poor fit and rework. Skipping the approval of the drawing and specification is another common error that causes disagreements after installation.

Our recommendation

Book the site visit before choosing a door, and ask the technician to check the frame's level, square and corrosion condition in writing. Approve the drawing and specification before production starts.

Summary

A site visit confirms whether your existing frame can take a new aluminum or iron door, and it gives you a drawing and specification before any work begins.

השאירו פרטים ונחזור אליכם