Commission a Bespoke Iron Pergola Gate for Your Garden Entry

t372-41

To commission an iron pergola gate for a garden entry, you share photos and measurements of the pergola and the opening, then receive a drawn specification to approve before production. The gate is fabricated to measure in our Tel Aviv factory, finished for outdoor use, and installed on site so it lines up with the pergola's lines and finish.

Why match the gate to the pergola

A garden entry is seen from the street and from inside the pergola, so the gate should look like part of the same structure. Matching the profile thickness, the bar spacing, and the color or finish makes the entry feel planned rather than added later.

Matching also helps practically. Gates and pergolas share the same weather exposure, so using the same galvanizing and powder-coating approach keeps both in step as they age.

What to prepare before the first call

Gather a few clear photos of the pergola, the garden entry, and the surrounding wall or fence. Note the planned opening width and height, the swing direction, and whether the gate will open inward or outward.

Photos from the street and from inside the garden
Rough measurements of the opening and the pergola posts
Preferred style: solid panels, open bars, or a mix
Any locks, intercom or automation you plan to add

How measuring and drawing work

After your inquiry we visit the site to measure the opening precisely, since walls are rarely perfectly square or level. We check the ground slope and the hinge points so the gate swings freely.

From these measurements we prepare a drawing and a written specification covering dimensions, materials, the frame and infill design, hinges and finish. You review it and approve it before any metal is cut.

Materials and finishing for outdoor use

Iron gives a traditional, heavy look, while aluminum is lighter and easier to operate. Both can be made to complement the same pergola design, and the choice depends on the size of the gate and how often it is used.

Outdoor metalwork is typically finished by hot-dip galvanizing for corrosion protection, followed by powder coating in the colour you choose. We discuss the finish with you during the specification stage so the gate and pergola share a consistent appearance.

Production and installation

Once approved, the gate is fabricated in our factory on Rival Street in Tel Aviv, where the frame, infill, and hardware are assembled and checked against the drawing. Fitting in the workshop first reduces surprises on site.

On installation day we set the posts or hinge points, hang the gate, and adjust the swing, latch and closing action. We then review the operation with you before leaving.

Safety and standards to confirm

A garden gate should close securely, avoid pinch points, and be stable on its hinges. For railings and guarding near the entry, Israeli standard SI 1142 applies in general terms, and we confirm exact dimensions with your engineer rather than guessing.

If the gate is automated, include the power source and safety reversing requirements in your brief so they are planned from the start.

Frequently asked questions

How long does a bespoke pergola gate take to commission?

Timing depends on the workload and the approval stage, so we confirm the schedule once the specification is agreed. Approving the drawing promptly helps keep the project moving.

Can the gate match an existing iron pergola exactly?

Yes, we can match the profile, bar spacing, and finish of an existing pergola. Sending clear photos and a few close-up shots of the metal helps us reproduce the look.

Do I need to be present for the site measurement?

It helps to be present so we can discuss the swing direction and the opening together. If you cannot attend, make sure someone with decision authority is available.

Can a gate be automated after it is installed?

Automation can be added, but it is easier to plan the wiring, hinge loads, and safety features at the design stage. Mention any automation plans in your first inquiry.

Common mistakes to avoid

Ordering a gate before measuring the actual opening, or ignoring the swing path and ground slope, often leads to a gate that rubs or cannot close properly. Choosing a finish without considering outdoor exposure can also shorten the gate's life.

Our recommendation

Send the photos and rough measurements first, then approve the written drawing before production starts. Ask for the finish to be confirmed in writing so the gate and pergola look consistent after installation.

Summary

A bespoke iron pergola gate is commissioned through photos, on-site measurement, an approved drawing, factory fabrication, and careful installation. Planning these steps early gives you a gate that matches your garden entry.

השאירו פרטים ונחזור אליכם