Custom Handrail Fabrication: Ordering Made-to-Measure Pieces

t353-38

Custom handrail fabrication means making each railing to the exact measurements, profile and finish of a specific project rather than choosing a standard stock item. The process runs from an inquiry with photos, to on-site measurement, a written drawing and specification, client approval, factory production and installation.

Why contractors and designers choose made-to-measure handrails

Standard handrails rarely fit a real staircase, balcony or ramp exactly. Wall conditions, floor finishes, landing heights and architectural details all change the geometry, so a bespoke piece often saves time on site.

Made-to-measure work also lets designers match the railing to the rest of the building, whether that means a slim steel profile, a glass infill or a specific powder-coated colour agreed with the architect.

Exact fit to the wall, stair or balcony edge
Design freedom in profile, infill and finish
Fewer on-site adjustments during installation

Preparing your inquiry with photos and basic information

The fastest way to start is a clear inquiry. Send photos of the area from several angles, including the surfaces the railing will attach to and any nearby elements such as steps, walls or existing rails.

Add a short note on what you need: indoor or outdoor use, the material you prefer, and any colour or finish requirements. If you already have a drawing or sketch, include it, as it helps us understand your intent before we visit.

On-site measurement and what we check

After reviewing your inquiry, we arrange a visit to measure the installation area. We record lengths, heights, angles, wall thickness and the condition of the fixing surfaces, and we note anything that could affect the design.

During the visit we also confirm access routes for transporting the finished pieces, so the handrail can be delivered and installed without surprises.

Drawing and written specification

Once measurements are complete, we prepare a drawing and a written specification. The drawing shows the layout, sections and fixing points, while the specification lists the material, profile, joints, infill, fixings and finish.

Exact structural values are checked with the engineer on your project. Where relevant, we refer to the Israeli railing standard SI 1142 in general terms, so the design is reviewed against the applicable requirements before anything is produced.

Client approval and factory production

The drawing and specification are sent for your approval. Please check dimensions, finish and details carefully, because changes after production starts are harder and slower to make.

Once approved, the pieces are cut, shaped and welded at our factory at 37 Rival Street, Tel Aviv. Finishing options include hot-dip galvanizing and powder coating, chosen to suit indoor or outdoor exposure.

Finishing, delivery and installation

After finishing, the handrail is checked against the approved drawing, packed to protect the coating and delivered to site. Installation follows the fixing details in the specification, with attention to alignment, level and secure anchoring.

Keeping the same drawing and specification throughout the process means the installed railing matches what was approved, which is the main goal of a made-to-measure order.

Frequently asked questions

How long does a custom handrail take to make?

Timing depends on the size of the order, the chosen finish and the current production schedule. We confirm the timeline with you once the drawing and specification are approved.

Do I need to be present for the on-site measurement?

It helps to be present or to have someone on site who can give access and answer questions about the wall, stair or balcony. We can arrange the visit around your schedule.

Can you work from a sketch instead of a full drawing?

Yes, a sketch with dimensions is a good starting point. We turn it into a proper drawing and specification after measuring the site.

Which finishes can I choose for an outdoor handrail?

For outdoor use, hot-dip galvanizing and powder coating are common options. We recommend the finish after reviewing the location and how exposed the railing will be.

Common mistakes to avoid

Ordering from measurements taken without checking the actual site, or approving a drawing without confirming dimensions and finish. Both lead to costly changes after production has started.

Our recommendation

Measure on site after the walls and floors are finished, and confirm the final fixing surfaces before approving the drawing. Share the specification with your structural engineer early so any required values are checked before production.

Summary

Custom handrail fabrication works best when the inquiry, measurement, drawing and approval are all completed before production. Following that order gives you a railing that fits the site and matches the design.

השאירו פרטים ונחזור אליכם