Custom Perforated Stainless Steel Panels Made to Measure

t475-34

A perforated stainless steel panel is a sheet of stainless steel with a pattern of holes, cut to your exact dimensions. It can serve as a privacy screen, ventilation cover, decorative facade element or safety guard. At Techno Kol Uzi, each panel is designed, cut and finished in our factory at 37 Rival Street, Tel Aviv, to suit the project.

What a Perforated Stainless Steel Panel Is

A perforated stainless steel panel is a flat sheet of stainless steel with holes punched or cut through it in a set pattern. The pattern can be round, square, slotted or a custom design, and the hole size and spacing change how much light, air and visibility pass through.

Because stainless steel resists corrosion, these panels suit both interior walls and exterior elements. They can be used as a screen, a ventilation cover, a decorative wall or a guard in front of equipment.

Common Uses for Perforated Panels

Designers and builders use perforated panels in many settings. Typical uses include:

Privacy screens for balconies and terraces
Ventilation grilles for technical rooms
Decorative facades and entrance walls
Protective guards around machinery or openings
Interior feature walls and ceiling elements

Each use calls for a different hole pattern, open area and panel thickness, so we confirm the purpose before we start drawing.

Choosing the Pattern, Hole Size and Open Area

The pattern decides the look and the performance of the panel. A small, dense pattern gives more privacy and less light. A larger, widely spaced pattern lets in more air and light but shows more of what is behind it.

The percentage of open area is a key figure to agree on early. We help you test pattern options on a drawing before cutting, so the panel meets both the visual goal and the practical need.

Our Fabrication Process

Every project follows the same steps. You send an inquiry with photos or a sketch. We visit the site to measure, then prepare a drawing and a written specification for your approval.

Once approved, the panel is cut in our factory with precise perforation, then deburred and finished. Stainless steel is handled carefully so the surface stays clean. The panel is then delivered and installed on site.

Installation and Structural Support

A perforated panel must be fixed to a frame that can carry its weight and any wind load. The support system depends on the panel size, the fixing points and the wall or floor it is attached to.

For railings and guards, the Israeli railing standard SI 1142 applies. Exact values for height, loads and spacing are checked with your structural or safety engineer before installation, and we work to those confirmed figures.

Why Work with a Factory Since 1945

Techno Kol Uzi has manufactured iron, aluminum, glass and stainless steel works since 1945, and today the business is run by the third generation of the family. Our experience with custom metalwork means we understand how a panel should be drawn, cut and fixed to last.

We work directly with private homeowners, building committees, contractors, architects and interior designers, and we give each project the same attention to detail, from the first measurement to the final installation.

Frequently asked questions

Can you make a perforated stainless steel panel in a custom pattern?

Yes. We can cut round, square, slotted or custom hole patterns to your design. We review the pattern on a drawing with you before fabrication starts.

What is the difference between a perforated panel and a mesh?

A perforated panel is a solid sheet with holes punched through it, while a mesh is made of woven or welded wires. Perforated panels are usually more rigid and give a cleaner, more solid appearance.

Is stainless steel suitable for outdoor perforated panels?

Stainless steel resists corrosion well, so it suits outdoor use. The right grade and finish depend on the location, and we advise you on this during the specification stage.

How do I start a project with you?

Send us an inquiry with photos or a sketch and the intended use. We then arrange an on-site measurement and prepare a drawing and specification for your approval.

Common mistakes to avoid

A common mistake is choosing a pattern by looks alone and ignoring open area, which affects airflow, light and privacy. Another is fixing the panel without confirming the support structure and load requirements first.

Our recommendation

Before you finalize the design, decide what the panel must do (privacy, airflow or protection) and test two or three hole patterns on a drawing. Confirm the support and fixing details with your engineer before the order is placed.

Summary

Perforated stainless steel panels combine strength, durability and a flexible design, and they can be made to any size and pattern. Careful planning of the pattern, open area and support makes the result work well.

השאירו פרטים ונחזור אליכם