Custom Stainless Steel Kick Plates for Iron and Aluminum Entrance Doors

t414-47

A stainless steel kick plate is a flat metal panel fixed to the lower part of an entrance door to absorb the impact of feet, carts and cleaning equipment. For iron and aluminum doors in busy buildings, a custom-made plate sized to the door leaf and fitted to the door's frame gives the best protection and a clean finish.

Why high-traffic doors need a kick plate

The lower third of an entrance door takes the most abuse. Shoes, trolleys, delivery boxes and mop buckets all strike it again and again, and over time the paint, powder coating or brushed finish wears through. A kick plate sits in that exposed zone and takes the damage instead of the door itself.

In residential buildings, shared entrances and commercial lobbies alike, a plate also keeps the door looking maintained for longer, which matters to building committees and property managers who are judged by the state of common areas.

Choosing stainless steel for the job

Stainless steel resists scratching, staining and corrosion better than painted metal, and it cleans easily with ordinary products. It suits both iron and aluminum doors because it sits alongside the existing finish without a chemical reaction at the contact line.

Brushed finish hides fine marks and suits most lobbies.
Mirror finish looks sharp but shows fingerprints more readily.
Gauge and edge detail should match the door's weight and use.

How the plate is measured and specified

Every plate starts with an on-site measurement. We check the door leaf height and width, the clearance above the threshold, and whether the door swings in or out, since that changes which face the plate covers. Photos help, but they never replace measuring the actual opening.

The result is a written specification and drawing showing the plate size, edge profile, finish and fixing method. You approve the drawing before anything is cut.

Fixing the plate to iron and aluminum doors

Fixing depends on the door material. Iron doors are often drilled and fixed with screws into the leaf, while aluminum doors may need concealed fixings or adhesive-backed mounting so the surface is not damaged. The method is agreed during the measurement visit.

Plates are set so their top edge is level and the gap to the threshold stays within what the door can clear. Any sealing or weather strip is checked so the new plate does not interfere with it.

Production and finishing at our Tel Aviv factory

At Techno Kol Uzi, Ltd., at 37 Rival Street in Tel Aviv, the plate is cut, bent and finished in our workshop. Stainless steel is worked to the drawn dimensions so the fit on site is straight and tidy rather than improvised.

Because we manufacture in-house, adjustments are made in the factory before installation, which keeps site work short and reduces disruption to residents or tenants using the entrance.

Installation and aftercare

Installation is done after the approved drawing is confirmed and the production is complete. We check alignment, operation of the door and clearance on every swing before leaving the site.

Clean with mild soap and water, then dry with a soft cloth.
Avoid steel wool and harsh abrasives that scratch the surface.
Check the fixings periodically in heavily used doors.

Frequently asked questions

Can a kick plate be fitted to an existing aluminum door?

In most cases yes, provided the door leaf has enough flat area and the fixing method suits the frame. We confirm this during the on-site measurement before any work is ordered.

Do I need to remove the door to fit a kick plate?

Usually not. Most plates are fitted with the door in place, although we may remove the door temporarily if the swing or fixing position requires it.

Which stainless steel finish is best for a busy lobby?

A brushed finish is generally the practical choice because it hides small scratches and fingerprints better than a mirror finish. Your choice can also be guided by the look of the existing door.

Will the plate affect how the door closes?

It should not, if the plate is sized and positioned correctly. We check the swing and clearance against the threshold and any seals before the plate is finally fixed.

Common mistakes to avoid

Ordering a plate from a photo alone and skipping the on-site measurement often leads to a poor fit. Ignoring the door's swing direction and threshold clearance can also cause the plate to rub or obstruct the door.

Our recommendation

Measure the door in person, confirm the swing and clearance, and choose a brushed stainless finish with a fixing method suited to your door material. Approve the written drawing before production so the plate fits the first time.

Summary

Custom stainless steel kick plates protect iron and aluminum entrance doors where traffic is heaviest, and a plate made to measure fits cleanly and lasts longer.

השאירו פרטים ונחזור אליכם