Custom Steel Emergency Exit Door Frames for Shops and Offices

t487-19

A custom steel emergency exit door frame is a welded steel frame built to the exact opening, wall thickness and door type of a shop or office, so the exit door opens fully, latches correctly and stays rigid over time. Standard frames often fail to fit unusual openings or heavier panic hardware, which is why a made-to-measure frame is often the practical choice.

What makes a steel frame suitable for an emergency exit

An emergency exit door has to do two things at once: stay closed against intruders during normal use and open immediately under pressure from inside. The frame carries the load of the door, the hinges and the locking hardware, so it must be stiff enough to keep the door square for years.

Steel is well suited to this job because it resists bending and impact. A properly designed steel frame keeps the door aligned, which is what allows the latch to release smoothly when someone pushes the bar.

Why custom sizing matters

Older shop fronts and office corridors rarely have standard openings. Walls may be out of plumb, thresholds may be uneven and the wall thickness may differ from one unit to another. A frame made to measure accounts for these details instead of forcing a standard door into a space it does not fit.

Custom work also lets the frame suit the hardware you need, whether that is a push bar, a closer or a specific hinge arrangement.

Key points to check before ordering

Before approving a design, confirm the following with your installer or engineer:

The clear opening width and height that the exit route must provide
The direction of swing and whether the door opens toward the escape direction
The type of push bar or panic hardware and its mounting requirements
The wall type and the anchoring method suited to it
The finish, such as hot-dip galvanizing or powder coating, for the site conditions

Exact dimensional requirements should be confirmed with the relevant engineer and the applicable standards for your building.

How the process works at our factory

We start with an inquiry and photos of the opening. Then we measure on site, because a few millimeters can decide whether a door closes properly. From the measurements we prepare a drawing and a written specification, which you approve before any steel is cut.

Production takes place in our factory at 37 Rival Street, Tel Aviv. After welding, the frame receives its finish, and it is then installed on site and checked for alignment, latch action and free opening.

Common requirements for shop and office owners

Shop owners often need the exit to stay usable while the shop is open to the public, so installation timing matters. Office managers usually need the work coordinated with the building committee or the contractor.

Keep the approved drawing and specification on file. If the building is inspected, having documented specifications makes it easier to show what was installed and why.

Maintenance and long-term performance

A steel frame is durable, but the door hardware still needs attention. Check that the push bar releases easily, that hinges are tight and that the door closes without rubbing. Clear the area in front of the exit so nothing blocks the swing.

If the door begins to drag or the latch hesitates, report it promptly. Small alignment problems are simpler to correct early than after the frame has been stressed for months.

Frequently asked questions

Can a steel frame be made for an existing opening?

Yes. We measure the existing opening on site and build the frame to those measurements, which is common for shops and offices with irregular walls.

Do you handle the hardware as well as the frame?

We can coordinate the frame with the hardware you choose, so the door, latch and mounting points work together. Confirm the specific hardware requirements with your engineer before ordering.

How do I know the exit meets the required standards?

Exact requirements depend on your building and use, so have your engineer or building inspector confirm the opening sizes and hardware. We build to the approved specification.

Where is your factory located?

Our factory is at 37 Rival Street, Tel Aviv, where we manufacture and finish all custom steel work.

Common mistakes to avoid

Ordering a door before measuring the actual opening, and choosing a finish without considering the site conditions, are the errors we see most often. Both can cause misfit doors and early corrosion that are costly to fix.

Our recommendation

Measure the opening yourself first, note the swing direction and the hardware you need, then have a professional measure on site before approving the drawing. This saves time and prevents fitting problems.

Summary

Custom steel emergency exit door frames give shops and offices a rigid, precisely fitted exit that works with the hardware and the wall as it actually is.

השאירו פרטים ונחזור אליכם