Getting a Balcony Guard Quote from Photos and Dimensions

What Information to Prepare Before You Write

A remote estimate is only as good as the information behind it. Before sending your request, gather the basic facts about the balcony or window where the guard will be installed. Accurate details help our team understand the job before we visit, which saves time for you and for us.

• Width and height of the opening, measured in centimeters
• Whether the guard goes inside or outside the opening
• The floor level and what sits below the balcony
• Your preferred style, such as vertical bars, a decorative pattern, or a simple grid

If you are unsure about any measurement, say so in your message. We would rather know than guess.

How to Take Useful Photos

Photos show us the setting in a way measurements alone cannot. Stand back far enough to capture the entire opening, including the frame, the wall around it, and any railings or tiles nearby. Good light helps, so shoot during the day without strong shadows across the area.

• One wide photo showing the full balcony or window
• One close photo of each corner of the opening
• A photo from inside and from outside if possible
• A photo with a tape measure next to the opening for scale

Avoid heavy filters or cropped images, since they can hide the edges we need to see.

Measuring the Opening Correctly

Measure the width at the top, middle, and bottom, and the height on the left, center, and right. Walls are rarely perfectly straight, so the smallest number is usually the one that matters for fitting. Write down all readings, not only one. Measure to the inside edge of the frame or to the wall, and note which one you used.

Also mention any obstacles such as air conditioning units, shutters, electrical boxes, or handles that could affect the placement of the guard. These details often change the design more than the size does.

What Happens After We Receive Your Request

Once your photos and dimensions arrive, our team reviews them and may ask a few follow-up questions. In most cases we then arrange an on-site measurement, because a final drawing needs to match the real opening. During the visit we confirm the dimensions, discuss the style with you, and check how the guard will be fixed to the wall or frame.

After the visit we prepare a drawing and a written specification for your approval. Production takes place in our factory in Tel Aviv, followed by finishing and installation. Nothing moves forward until you approve the drawing.

Choosing Iron or Aluminum for Your Guard

Iron is a strong, traditional choice for security bars and suits most balconies and windows. Aluminum is lighter and does not rust in the same way, which can be helpful in exposed areas. Both can be finished to match your building or home, and we will explain the differences that matter for your specific location.

Tell us whether the guard faces the sea, sits under a sheltered balcony, or is close to a garden, since these conditions affect the finish. For railing heights and safety requirements, the Israeli railing standard SI 1142 is the general reference, and we confirm exact values with the engineer for each project.

Tips for a Smooth Quote Process

A clear request usually leads to a faster and more accurate response. Keep your message short and organized, and attach all photos in one place. If you are a building committee, contractor, architect, or interior designer, mention the project name and the number of openings so we can plan the work together.

• Send all photos and measurements in one message
• Label each opening, such as living room window or balcony door
• Share any reference images of the style you like
• Note your preferred contact method and availability

Frequently asked questions

Can you give a quote without visiting the balcony?

We can review your photos and dimensions first to understand the job. For a final drawing and specification, we usually arrange an on-site measurement to confirm the details.

Which measurements do I need to send?

Send the width and height of the opening at several points, and note whether the guard goes inside or outside the frame. Mention any obstacles like air conditioners or shutters.

Do I need professional photos?

No, phone photos work well. Take a wide shot of the whole area, close shots of the corners, and one with a tape measure for scale.

Can I choose the design from my own reference picture?

Yes, you can send a reference image. Our team will explain how the design can be adapted to your opening and to the materials we work with.

Common mistakes to avoid

Sending a single measurement instead of several readings, or cropping photos so the edges of the opening are missing. Both can lead to a guard that does not fit correctly.

Our recommendation

Measure the opening at three points for both width and height, use the smallest reading for fitting, and attach photos taken from a distance so the whole area is visible.

Summary

Clear photos and accurate measurements make a remote balcony guard quote faster and more reliable. Our team then confirms everything on site before production begins.

Related guides

• Installation Timeline for Multi-Unit Window Bar Projects in Residential Blocks
• Measuring Window Openings Accurately Before Ordering Custom Security Bars
• Scheduling Balcony Screen Installation Around Tenant Occupancy
• Frame Reinforcement Brackets for Window Bars Installed in Hollow Blocks
• Acoustic Benefits of Perforated Aluminum Balcony Screens on Busy Streets
• Lockable Window Bars With Keyed Release for Shared Apartment Access
• All models in this category