Handrails for Wheelchair Ramps at Entrances Tel Aviv

t356-4

A wheelchair ramp at a building entrance needs continuous handrails on both sides, mounted at the correct height and extended beyond the ramp ends. Handrails should be sturdy, easy to grip, and finished in a corrosion-resistant material suited to outdoor use. Exact dimensions should always be confirmed with the project engineer against the applicable Israeli standard.

Why ramp handrails matter at building entrances

A ramp is only usable if people can hold on to it. Handrails give wheelchair users, elderly residents, parents with strollers and anyone with limited balance a secure point of support, especially on slopes and near the landing.

For building managers, handrails also reduce the risk of falls at the entrance, which is where traffic is heaviest and where wet weather makes surfaces slippery. A well-designed rail protects both residents and visitors.

Key design points for an accessible ramp rail

Good ramp handrails are continuous, meaning they run the full length of the slope without gaps, and they are installed on both sides where space allows. The grip should be round or slightly oval, with a diameter that fits a comfortable hand grasp.

Continuous rail along the full ramp length
Extension beyond the top and bottom of the ramp
Clear space between the rail and the wall
Rounded ends that do not catch clothing

Mounting height and extensions

Mounting height and extension lengths are set by Israeli accessibility requirements, including the general railing standard SI 1142, and by the specifics of each entrance. Exact values should be checked with the engineer for every project rather than copied from a generic guide.

Our team measures on site before drawing the rail, so that the height, the slope and the landing position are all taken into account. This avoids a rail that looks right but does not function for the user.

Choosing materials for outdoor entrances

Entrance rails face rain, sun and salt air, so material choice matters. Hot-dip galvanized steel with a powder-coated finish is a common choice for durability, while stainless steel suits areas where a clean, modern look is preferred. Aluminum is lightweight and resists corrosion well.

Ask for the finish to be specified in writing, including the coating type, so the building committee knows exactly what is being installed.

The made-to-measure process at Techno Kol Uzi

Every ramp is different, so we follow a clear process. It starts with an inquiry and photos of the entrance, followed by an on-site measurement. We then prepare a drawing and a written specification for your approval.

Inquiry with photos
On-site measurement
Drawing and written specification
Client approval
Production in our Tel Aviv factory
Finishing and installation

Installation tips for building managers

Plan the installation so that the ramp is not in use during fixing, and confirm the wall or floor base can carry the anchors. Check that rails are fixed firmly, since a loose rail is worse than none. After installation, test the rail by pulling on it and walking the full ramp.

Schedule a short review after the first season of rain and use, to catch any loosening or coating wear early.

Frequently asked questions

Do ramps need handrails on both sides?

Where space allows, handrails on both sides are recommended so that users can grip whichever side suits them. The exact requirement depends on the ramp layout and the applicable standard, which the engineer will confirm.

How high should a ramp handrail be?

The mounting height is set by Israeli accessibility requirements and should be checked against the standard for each project. We measure on site so the height suits the actual slope and entrance.

What material is best for an outdoor ramp rail?

Hot-dip galvanized steel with a powder-coated finish and stainless steel are both good options for outdoor entrances. Aluminum is also suitable because it is lightweight and corrosion resistant.

Can handrails be made to fit an existing ramp?

Yes, every rail is made to measure. We visit the entrance, measure the ramp and landings, and prepare a drawing for approval before production begins.

Common mistakes to avoid

Choosing a rail height or length without measuring the actual ramp is the most common error, as is leaving the rail without extensions at the top and bottom. Using a finish not suited to outdoor conditions also leads to early corrosion.

Our recommendation

Ask for an on-site measurement and a written specification before ordering, and confirm the mounting height and extensions with your engineer. Specify the finish in writing so the rail lasts through years of weather.

Summary

Well-designed ramp handrails make building entrances safe and usable for everyone. Measure carefully, choose a durable outdoor finish, and confirm the details with the engineer.

השאירו פרטים ונחזור אליכם