How to Measure Your Space for a Glass Display Case

t427-31

To measure space for a glass display case, record the exact width, height and depth at the exact spot where it will stand, measuring at several points because walls are rarely perfectly straight. Add notes on floor levelness, door swing, lighting and access routes so the factory can design a vitrine that fits and works in your room.

Why accurate measurements matter

A glass vitrine is made to measure, so the dimensions you send are the basis of the entire drawing. A few millimeters of error can mean a panel that does not fit, a gap that looks unfinished, or a door that rubs against the frame. Taking careful measurements once saves time for you and for the workshop.

Measure the space itself rather than relying on the plan alone. Plans are often drawn before finishing work, and actual walls, floors and ceilings can differ from what is drawn.

Measuring width, height and depth

Take each dimension at three points: near the left wall, the center, and the right wall for width. Use the smallest value as your reference when the space narrows, and note any difference you find.

Width: measure wall to wall at floor level and at top level.
Height: measure from the finished floor to the ceiling or to the point where the unit will stop.
Depth: measure from the wall outward to the front edge where the glass will sit.

Checking walls, floors and obstacles

Walls and floors are rarely perfectly straight or level. Note whether the floor slopes, whether the wall bulges, and whether skirting boards, electrical sockets, switches or pipes sit where the vitrine would stand. Mark these on a simple sketch so the designer can plan around them.

If the vitrine will be fixed to the wall or floor, tell us what the surface is made of, since the fixing method depends on it.

Allowing for doors, access and clearance

Think about how the vitrine will be used. Check the swing of nearby doors, the width of corridors, and whether you need space in front to open a glass door or reach inside. A display that is technically the right size can still feel cramped if people cannot walk past comfortably.

Leave room for the glass door to open fully without striking furniture or the wall, and consider where staff or visitors will stand while using the case.

Considering lighting, power and ventilation

If you plan to add lighting inside the vitrine, note where power outlets are located and whether cables can be routed discreetly. Lighting elements and transformers may need a small allowance in depth or height, so mention your plans early.

Consider heat from nearby windows or lamps and whether the location gets direct sunlight, as these affect both the display and the comfort of the room.

Sending your measurements to the workshop

Once you have your numbers, send us a clear sketch, a few photos of the space, and a short description of what the vitrine should hold. We will review the information, arrange an on-site measurement if needed, and prepare a drawing and written specification for your approval before anything goes into production.

Measuring with a steel tape, writing every figure with its unit, and labeling each sketch point makes the process smooth for everyone.

Frequently asked questions

Should I measure once or several times?

Measure at least three points for width and height, because walls and floors are often uneven. Record all values and let the workshop confirm them on site if the space is critical.

What if my wall is not straight?

Note where the wall bulges or recedes and send a photo with a marked sketch. The design can account for small irregularities during the on-site check.

Do I need to include the door when measuring?

Yes, include the swing area and any handles or frames it affects. This ensures the glass door opens fully without hitting furniture or walls.

Can I send photos instead of measurements?

Photos help a lot, but they do not replace exact measurements. Send both, and an on-site measurement can confirm the final figures before production.

Common mistakes to avoid

The most common mistake is measuring only once in one spot and ignoring floor slope or wall irregularities. Forgetting door swing, sockets and lighting needs also leads to rework.

Our recommendation

Mark your measurements on a simple sketch, note every obstacle, and let the workshop verify the numbers on site before approving the drawing.

Summary

Measure width, height and depth at several points, check walls, floors, doors and power locations, and send everything with photos for an accurate custom vitrine.

השאירו פרטים ונחזור אליכם