Ordering a Custom Sliding Gate for Your Home Entrance

t283-8

To order a custom sliding gate for your home entrance, send us photos and the approximate width of the opening, then we visit to measure on site. You receive a drawing and written specification for approval before we manufacture the gate in our Tel Aviv factory and install it at your home.

Start with photos and a short description

The first step is a simple inquiry. Send us clear photos of the entrance from the street and from inside the property, along with a short note about what you need: a single or double sliding leaf, whether you want an electric motor, and how the gate should look. Photos help us understand the surroundings, the wall or pillar construction, and the slope of the driveway before we ever come out.

Tell us if there are existing posts, a curb, or a fence that the gate must connect to. Even rough details save time later.

On-site measurement by our team

After reviewing your inquiry, we arrange a visit to measure the opening precisely. We check the clear width, the height available, the ground level, and whether the track can be set level. Sliding gates depend heavily on a straight, stable track, so we also look at the foundation and the space needed on the side where the leaf will slide.

Clear opening width and height
Ground slope and track base condition
Space for the gate to open or slide
Position of electric cabling and power point

Drawing and written specification for approval

Once we have the measurements, we prepare a drawing showing the gate dimensions, frame layout, infill pattern, and position of the motor and track. A written specification accompanies it, describing materials, finishing, and the installation details agreed for your entrance.

Please review the drawing carefully. Ask about anything unclear, such as the style of the bars or the placement of the gate post. Nothing goes into production until you have approved the drawing and specification in writing.

Production in our factory

After your approval, the gate is manufactured in our workshop at Rival Street 37 in Tel Aviv. Steel sections are cut, welded and assembled to the drawing, and the frame is checked for square and straightness before finishing. Working in the factory lets us control the quality of every joint rather than adjusting on site.

For outdoor gates we use a protective finish, typically hot-dip galvanizing followed by powder coating, so the gate handles Israeli weather well over the years.

Finishing and colour selection

Finishing is where the gate gets its character. You can choose the powder coating colour to match your windows, facade, or fence. We can also discuss infill patterns, from clean vertical bars to more decorative designs, so the gate fits the style of your home.

We will confirm the final colour and finish with you before coating, since changing it afterwards is not practical.

Installation at your home

Our team installs the gate at your property. We set the track or hinge posts, hang the leaf, connect the electric motor if selected, and test the opening and closing movement together with you. We also show you how the remote or control system works and how to keep the track clean.

Before we leave, we make sure the gate runs smoothly, stops safely, and sits level, so you can use it from the first day.

Frequently asked questions

Do I need to be home for the site visit?

It is best if you or someone with access to the entrance is present, so we can check the opening and discuss the layout with you. We can coordinate a suitable time with you after your inquiry.

Can I choose an electric motor for my sliding gate?

Yes, electric sliding and swing gates can be supplied with a motor and remote control. We confirm the motor type and power point during the on-site measurement.

Will I see the design before the gate is made?

Yes. You receive a drawing and written specification, and production begins only after you approve them in writing.

How do I know the gate will suit my home?

Sending clear photos and measurements at the start helps us plan the right design. The drawing stage lets you confirm the style, size, and finish before anything is manufactured.

Common mistakes to avoid

Ordering a gate based on an old measurement or without checking the ground for the track often causes fitting problems later. Measure on site with a professional before you finalise the design.

Our recommendation

Before you order, check that the track base is level and firm, and decide early whether you want an electric motor so the power point can be planned. Keep the drawing approval step, because it is the best way to avoid surprises at installation.

Summary

A custom sliding gate is ordered in clear steps: photos, on-site measurement, approved drawing, factory production in Tel Aviv, and professional installation at your home.

השאירו פרטים ונחזור אליכם