Requesting a Safety Assessment for Your Automatic Gate

t291-45

A gate safety assessment is an on-site check of an electric sliding or swing gate for pinch points, sensor function, stopping force, and the condition of motors, rails and hinges. To request one, send photos and a short description of the gate to Techno Kol Uzi, and we will schedule an inspection and provide a written report with recommendations.

What a Gate Safety Assessment Covers

A gate safety assessment looks at how your automatic gate behaves in everyday use, not only whether it opens and closes. The technician checks the gap between moving leaves and posts, the travel path of sliding gates, and any spot where a hand, foot or child could be caught.

Safety sensors, photocells and safety edges
Stopping and reversing behaviour when an obstacle is met
Condition of wheels, rails, hinges and stops
Motor, control unit and emergency release

The result is a clear picture of what works, what needs adjustment, and what should be replaced.

When You Should Request an Inspection

Book an assessment if the gate reverses late, makes grinding or jerky movements, or has been installed for several years without a check. Changes in the building, a new family member, or a recent repair are also good reasons to review the setup.

Gates that were installed by another party or that have been modified over time deserve a fresh look, since original settings may no longer match how the gate is used today.

How to Prepare for the Visit

Good preparation helps the technician finish the job efficiently. Note any problems you have seen, such as the gate stopping unexpectedly or sensors not responding, and when they happen.

Take clear photos of the gate, posts and sensors
Confirm the gate is accessible from both sides
Tell us the gate type: sliding or swing, and whether it is driven by one or two motors
Have any previous service paperwork ready if you have it

Our Inspection Process

We begin with your inquiry and photos, then arrange an on-site visit to measure and test the gate. After the inspection we prepare a written specification describing the findings and the recommended work, so you can review it before anything is changed.

Approved work is carried out in our Tel Aviv workshop where possible, and installation follows the same careful steps used for new gates, from drawing through finishing and fitting.

Understanding Safety Requirements in Israel

Automatic gates and railings in Israel are expected to meet the relevant safety standards, including the Israeli standard SI 1142 for guarding and railings. Those standards address openings, heights and forces in a general way, and the exact values that apply to your installation are checked with the project engineer.

We do not rely on memory for these figures. During the assessment we identify the points that need to be verified against the applicable requirements and document them in the report.

What Happens After the Assessment

You receive a written report that lists each item checked, its condition, and the recommended action. Some findings are simple adjustments that can be made during the visit, while others may call for new sensors, safety edges or motor parts.

You decide which recommendations to proceed with. Nothing is installed without your approval of the written specification, so you stay in control of the scope and the timing of any work.

Frequently asked questions

How long does a gate safety assessment take?

Most assessments are completed in a single visit, depending on the size and number of gates. Complex installations with several motors may need more time for testing.

Do I need to be present during the inspection?

It is helpful if you or someone familiar with the gate can attend, so questions about daily use can be answered on the spot. Please confirm access arrangements when you book.

Can you assess gates you did not install?

Yes. We assess gates from any source, since the safety of an existing gate depends on its current condition and settings, not on who installed it.

Will I receive a written report?

Yes. Every assessment ends with a written report and recommendations, which you can review before deciding on any repairs or replacements.

Common mistakes to avoid

Many owners wait until a gate fails or hits someone before checking its safety, and they assume a gate that opens smoothly is automatically safe. Sensors and stopping force can drift out of adjustment without any visible sign.

Our recommendation

Schedule an assessment at least once a year, and after any repair or change to the gate or its surroundings. Keep the written report with your building or property documents so the history of the gate is clear to future technicians.

Summary

A gate safety assessment checks sensors, stopping behaviour, moving parts and motors on your automatic gate, and ends with a written report. Send us photos and a short description to book an inspection at Techno Kol Uzi.

השאירו פרטים ונחזור אליכם