Restaurant Balcony Stair Railing Order: Step-by-Step Process

t326-17

A restaurant railing order starts with an inquiry and photos, followed by an on-site measurement and a written drawing and specification you approve before production. The railing is then made to measure in our Tel Aviv factory, finished with hot-dip galvanizing or powder coating, and installed on site. Following this sequence keeps the balcony safe, compliant and ready on the planned date.

Why restaurant balconies need a dedicated order process

A restaurant balcony or outdoor stair is used by guests, staff and sometimes deliveries, often in wet and crowded conditions. That means the railing has to handle more traffic than a typical home stair, and it has to look right next to your dining area. Treating the order as a planned project rather than a quick purchase helps avoid rework and delays during a busy season.

Before you contact us, think about who uses the stair, how many people pass through at peak hours, and how the railing will sit next to your existing signage, lighting and furniture.

Step 1: Send an inquiry with photos

Start by sending us a short description and clear photos of the stair or balcony. Wide shots help us understand the space, while close-ups of the existing railing, the wall or the floor edge show how the new railing will attach.

Photos from the bottom and top of the stair
Approximate length and height of the run
Whether the railing is for an indoor or outdoor area
Any preferred finish or colour

Step 2: On-site measurement

After reviewing your inquiry, we arrange a visit to measure the stair accurately. Precise measurements matter because steps, landings and wall edges are rarely perfectly uniform. We check the stair width, the step nosing, the wall or floor fixing points and any obstacles such as lighting or drainage.

We also note how the railing will meet the glass, the balustrades or the restaurant entrance, so the finished work fits cleanly.

Step 3: Drawing and written specification for approval

Once measurements are confirmed, we prepare a drawing and a written specification. The document shows the railing design, the materials, the finish, the fixing method and the layout of the posts and infill. You review it and approve it in writing before any production starts.

This is your chance to request changes, such as a different infill pattern or a handrail profile. Approving the drawing early prevents costly corrections later.

Step 4: Production and finishing in the factory

After approval, the railing is manufactured in our factory at 37 Rival Street, Tel Aviv. Steel parts are cut, welded and assembled to the measurements from your drawing. Finishing follows, typically hot-dip galvanizing for corrosion protection and powder coating for the final colour and look.

Galvanizing and powder coating are especially suitable for outdoor restaurant areas exposed to sun, rain and sea air.

Step 5: Installation and final checks

On the agreed date, our team installs the railing on site. We fix the posts, align the handrail, and check that the height, spacing and fixings meet the requirements of the Israeli railing standard SI 1142. For exact values, we confirm the specifics with the engineer on your project, since the correct dimensions depend on your building and use.

We check the finished railing with you before handover, so you can confirm that it is level, secure and ready for guests.

Planning your restaurant railing project

To keep your opening or renovation on track, plan the railing order early and allow time for measurement, approval and production before installation. Share your opening date and any inspection deadlines at the first inquiry, so we can plan the schedule with you.

Inquiry with photos and basic dimensions
On-site measurement visit
Approved drawing and specification
Factory production and finishing
Installation and final check

Frequently asked questions

How long does the restaurant railing order process take?

The timeline depends on the size of the project, the design approval and the current production schedule. We confirm the expected timing with you once the drawing and specification are approved.

Do I need to be present for the on-site measurement?

It helps if someone who knows the space is present, such as a manager or the contractor. This lets us clarify fixing points and any site conditions during the visit.

Can the railing be finished to match my restaurant's design?

Yes. Finishes such as powder coating can be chosen to match your interior or exterior style, and the choice is confirmed in the approved specification.

Why is the drawing approval step important?

The approved drawing fixes the design, materials and layout before production begins. Changing the design after production is far more difficult and can delay your installation.

Common mistakes to avoid

Ordering before measuring the stair or skipping the written approval can lead to railings that do not fit or do not meet the required standard. Always confirm the drawing and specification in writing before production begins.

Our recommendation

Measure and photograph the stair before you request a quote, and plan the installation for a quiet period so the restaurant is not disrupted. Ask for the drawing early, because approving it first keeps the rest of the schedule predictable.

Summary

A restaurant railing order runs from inquiry and photos through on-site measurement, approved drawings, factory production and finishing, to professional installation. Following these steps keeps your balcony safe, compliant and ready on time.

השאירו פרטים ונחזור אליכם