Storage Yard Fence: Secure Outdoor Stock and Lumber

t300-34

A storage yard fence is a custom iron or aluminum barrier that keeps unauthorized people out of outdoor stock and lumber areas. Iron offers strength and resistance to forced entry, while aluminum offers lighter weight and low maintenance. We design, measure and manufacture the fence to match your site, gate traffic and security needs.

Why Outdoor Storage Needs a Proper Fence

Outdoor inventory, timber, pipes and building materials are valuable, and they are often left in open areas overnight. A low or flimsy barrier invites theft and damage, and it does little to stop someone determined to get in. A well-built fence sets a clear boundary, makes the site look managed, and slows intruders down long enough to be noticed. For many business owners, it is the first layer of protection that every other measure depends on.

A fence also helps you control who comes and goes, which matters when deliveries, contractors and staff share the same yard.

Choosing Between Iron and Aluminum

Iron is the choice when maximum strength and resistance to cutting or climbing matter most. Once hot-dip galvanized and finished with powder coating, it holds up well to weather and heavy use. Aluminum is lighter, will not rust, and needs less upkeep, which suits sites near the coast or areas where maintenance visits are hard to schedule.

Iron: highest strength and deterrence
Aluminum: lightweight and low maintenance
Combination: solid iron base with aluminum infill

Height, Design and Visibility

Height is one of the first decisions. A taller fence discourages climbing, but it can also block the view from the street or from your office. Many owners choose a solid lower section with an open upper section, so the yard stays visible while the perimeter remains firm. Vertical bars spaced closely make climbing difficult and leave no footholds.

Consider lighting and sightlines together with the fence design. A fence that lets your staff see the whole yard is often more effective than a solid wall that hides activity.

Gates and Access Control

The gate is where most fences are tested, so it deserves careful planning. Think about the size of the trucks and forklifts that enter, how often the gate opens, and whether it should swing or slide. Electric sliding gates suit busy yards, while manual swing gates can work for smaller sites. Locks, hinges and posts should be sized for the weight and frequency of use.

Plan for pedestrian access as well, so staff do not need to open the main gate for every entry.

Measuring, Drawing and Installation Steps

We start with an inquiry and photos of the site, followed by an on-site measurement of the perimeter, ground conditions and gate positions. Based on that, we prepare a drawing and a written specification for your approval. Once approved, the fence is produced in our factory and finished by hot-dip galvanizing or powder coating, then installed on site.

Inquiry with photos
On-site measurement
Drawing and specification
Approval, production and finishing
Installation

Safety, Codes and Final Checks

Railings and barriers in Israel are expected to meet the relevant standard, including the general Israeli railing standard SI 1142 where it applies. Exact dimensions and load requirements are confirmed with the engineer for your specific site, so we do not guess at values. Check that gates open fully without blocking walkways, that posts are set firmly, and that sharp edges are finished safely.

A final walkthrough after installation confirms that the fence performs as planned before you hand the site back to daily operations.

Frequently asked questions

Is iron or aluminum better for a storage yard fence?

Iron gives the greatest strength and resistance to forced entry, while aluminum is lighter and needs less maintenance. Many sites choose iron for the perimeter and gates, depending on the level of security needed.

How high should a storage yard fence be?

Height depends on your security needs, local conditions and whether you need to see into the yard. We recommend discussing your site on-site so the height and design can be confirmed with the engineer.

Can the fence be built to fit an uneven or irregular site?

Yes. Because every fence is made to measure, panels and gates can be adapted to the exact dimensions and ground conditions of your yard.

Do you install the fence as well as manufacture it?

Yes. We manufacture in our Tel Aviv factory and carry out the installation after the drawing is approved and the finishing is complete.

Common mistakes to avoid

Choosing a fence based only on appearance, or ignoring the gate size and traffic, often leads to a barrier that is easy to bypass or difficult to use. Measure your vehicles and plan the gate before you decide on height and material.

Our recommendation

Start with a site visit and a written list of what you need to protect and how trucks and staff move through the yard. Ask for a drawing and specification before approving production, so the fence matches your real operations.

Summary

A custom iron or aluminum storage yard fence protects your outdoor inventory with a design built around your site, gate traffic and security needs. Measure first, plan the gate, and approve a clear drawing before production begins.

השאירו פרטים ונחזור אליכם