Warehouse Yard Bollard and Guardrail Solutions

t494-17

Warehouse yard bollards and guardrails are steel barriers that guide vehicles, protect building corners and loading docks, and separate traffic from pedestrians. They are designed to the specific layout, vehicle types and turning paths of each site, and manufactured to measure in steel with a protective finish.

Why warehouse yards need dedicated protection

Yards are where heavy trucks, forklifts and delivery vans meet walls, columns, fuel points and people. Without physical protection, every maneuver puts the building fabric and the staff at risk. Bollards and guardrails absorb small impacts that would otherwise chip concrete, dent cladding or damage sensitive equipment.

A good barrier scheme is planned at the same time as the yard layout, not added later when damage has already happened.

Choosing between bollards and guardrails

Each element does a different job, and many yards use both.

Bollards protect corners, column bases, gate posts and building entrances from direct impact.
Guardrails run along edges, ramps and walkways, keeping vehicles and pedestrians on their side of the line.
Removable bollards allow fire access routes or occasional heavy deliveries to pass when needed.

We discuss which combination suits your traffic pattern during the site visit.

Planning positions and spacing

Position is the most important decision. Bollards should be placed where vehicles realistically turn, reverse or stop, not only at the obvious corners. Spacing must leave enough clear width for the largest vehicle using the yard, and must not block door swings, hydrants or drainage gullies.

Exact installation dimensions and clearances are verified together with your structural or civil engineer against the applicable standards for your project.

Materials and finishes for industrial exposure

Yards are harsh: rain, washing water, salt air and constant knocks. We manufacture from structural steel and finish it by hot-dip galvanizing, then apply powder coating where a colour or extra protection is needed. Stainless steel is an option for areas with washdown or chemical exposure.

For bollards that may take heavy impacts, the steel section, wall thickness and base plate design are selected together with the engineer.

From drawing to installation

The process starts with your site plan and photos of the yard. We carry out an on-site measurement, then prepare a drawing and a written specification for your approval. Production takes place in our factory, followed by galvanizing or coating and then installation.

Inquiry with plan and photos
On-site measurement
Drawing and specification for approval
Factory production and finishing
Installation on site

Working with architects and site planners

We supply the details architects and site planners need: fixing types for slab or ground-bearing bases, section profiles, and layout sketches that can be integrated into your drawing set. If your design calls for a particular look, such as a sleek steel bollard or a matching guardrail along a building facade, we can adapt the profile to suit the architecture.

Early contact helps avoid conflicts with utilities and drainage, which are much easier to solve before the yard is poured.

Frequently asked questions

Do warehouse yard bollards need to be fixed into concrete?

Usually yes. Most bollards are set into a concrete foundation or fixed to a slab with anchors, and the method depends on the ground and expected impact. The fixing design is confirmed with your engineer.

Can bollards be removable for deliveries or fire access?

Yes. Removable or lockable bollards can be designed for yards that need occasional clear passage. We recommend agreeing the operating procedure with the site manager before the layout is finalized.

How do you protect steel bollards from rust in a yard?

We use hot-dip galvanizing as the base protection and add powder coating where a colour or extra durability is required. The right finish depends on exposure and cleaning practice on site.

Can you match the bollards to the building design?

Yes. We can adapt the profile, height and finish so the bollards and guardrails complement the architecture and the wider site design.

Common mistakes to avoid

Placing bollards only at obvious corners and forgetting the real turning paths of trucks, or blocking hydrants, doors and drainage. Check the layout with the largest vehicle before fixing anything.

Our recommendation

Walk the yard with the drivers who use it every day and mark where they actually turn and reverse before finalizing bollard positions. Share that plan with us early so the drawing reflects real movement.

Summary

Well-placed, galvanized steel bollards and guardrails protect buildings and people in warehouse yards and last for years when planned with the site layout.

השאירו פרטים ונחזור אליכם