Wrought Iron Arched Gate Frame Dimensions Guide

t302-20

A wrought iron arched gate frame is sized from the clear width and height of the opening, with the arch built as a curved top section above the straight sides. Measure the opening at several points before ordering, because walls are rarely perfectly square or level. Exact structural values depend on the gate's weight and the posts, so they are confirmed with the engineer after the on-site measurement.

Start with the clear opening

The first measurement is the clear opening between the posts or pillars, from inside face to inside face. Measure the width at the bottom, middle and top, because an old wall may be slightly out of line. Then measure the height from the finished ground level to the highest point you want the arch to reach.

Write down every measurement, along with any slope in the driveway. A gate that opens over a sloped surface needs extra clearance at the bottom edge.

Plan the arch height and rise

The arch is the curved part above the straight sides of the frame. Its rise, meaning how far the top curve peaks above the springing line where the curve starts, changes both the look and the amount of steel in the frame.

A low, shallow arch suits wide openings and modern homes.
A taller arch suits classic or Mediterranean facades.
Keep enough height for any gate lintel, lighting or intercom above the frame.

Decide on the frame width and bar spacing

The frame width is the section of the gate that carries the infill bars or decorative panels. Wider sections handle more weight and wind load, while narrower sections look lighter. The spacing between vertical bars affects both safety and appearance, so agree on it during the design stage.

For the railing and fence side of the project, Israeli practice refers to the standard SI 1142 for guardrail requirements. Exact values are checked with the engineer for your specific site.

Account for gate weight and hinges

A wrought iron arched gate can be heavy, especially with a full frame and solid panels. The weight determines the hinge type, the post strength and whether the gate needs a wheel or counterweight. Tell us the approximate design early, so the hinges and posts are matched to the frame.

Check that the posts can carry the load without leaning, especially if the gate is wide or opens onto a slope.

Allow for finishing and galvanizing

Finishing adds a thin layer of material to the surfaces, so the fit between the gate and the opening must include a small gap. Hot-dip galvanizing and powder coating protect the steel from rust, and the finished size should be confirmed after the coating is applied.

Ask whether the drawing shows finished dimensions or raw steel dimensions, so there are no surprises at installation.

Confirm the drawing before production

A written specification with a dimensioned drawing is the step that prevents most errors. The drawing should show the clear opening, the arch rise, the frame width, the bar spacing and the hinge positions. Review it carefully and approve it in writing before the steel is cut.

Once the drawing is approved, production starts in our factory and the gate is installed on site.

Frequently asked questions

Should I measure the opening myself or have it measured on site?

You can take rough measurements yourself, but an on-site measurement by the manufacturer is more reliable. Walls and posts are often out of square, and a professional check catches this before production.

Does the arch add extra weight to the gate?

Yes, the curved top section adds steel and therefore weight compared with a straight gate of the same width. The exact difference depends on the design and is calculated in the drawing.

Can an arched gate be automated?

Many arched gates can be fitted with an automatic operator, but the weight, width and mounting points must be checked first. We confirm the suitability during the design and measurement stage.

Why does the drawing need to be approved before production?

Once steel is cut and welded, changes are costly and time-consuming. A signed-off drawing ensures the gate fits the opening and matches what you expected.

Common mistakes to avoid

The most common mistake is measuring the opening once at one height and ordering without checking the top and bottom widths. Forgetting the finishing thickness and the ground slope also leads to a gate that does not fit.

Our recommendation

Measure the opening at three heights and three widths, note any slope, and send photos with the measurements so the design can be checked before production. Approve a dimensioned drawing in writing before any steel is cut.

Summary

Accurate measurement of the clear opening, arch rise, frame width and hinge positions is the key to a wrought iron arched gate that fits and works well. Confirm every dimension on a written drawing before production.

השאירו פרטים ונחזור אליכם