Aluminum Fence Dismantling and Reinstallation in Israel

t307-45

Yes, an aluminum fence can usually be carefully dismantled, moved and reinstalled at a new position, provided its panels, posts and fixings are in sound condition. Techno Kol Uzi takes the fence down, checks each component, repairs or replaces what is damaged, and fits it to the new line with a written specification. The result is a fence that looks and performs like new.

When Moving an Aluminum Fence Makes Sense

Many owners decide to move a fence when a property line changes, when a garden is rebuilt, or when a new extension leaves no room for the existing line. Relocating a fence is often more practical than buying a completely new one, especially when the original panels are still solid and the design suits the home.

Before deciding, consider the condition of the aluminum and the posts. Older fixings may be worn, and some sections may have been bent during the first installation. A short inspection helps you understand what can be reused and what should be replaced.

How the Dismantling Is Done Carefully

Careful dismantling protects both the fence and the surrounding ground. We first photograph the existing layout and mark each panel so it returns to the correct position. Posts are released from their bases, and fixings are removed without forcing components apart.

Photograph and label every section
Remove fixings without stripping threads
Protect finishes during handling and transport

Inspection, Repair and Finishing

Once the fence is in the workshop, each component is checked for straightness, cracks, corrosion and worn coating. Damaged parts are straightened or replaced, and missing fixings are supplied to match the original design as closely as possible.

If the fence is iron, it may need surface preparation and a fresh coat of protective finish, such as hot-dip galvanizing or powder coating, before reinstallation. Aluminum sections are cleaned and checked so the new installation looks uniform.

Measuring and Planning the New Line

Accurate measurement is the foundation of a successful reinstallation. We survey the new route on site, noting slopes, level changes, gate positions and any obstacles. Post spacing and panel lengths are adjusted to suit the ground while keeping the design visually consistent.

You receive a drawing and a written specification for approval before any work starts, so the final result matches what you agreed to.

Reinstallation on Site

On site, posts are set plumb and aligned with the marked line before panels are fitted. We check levels continuously so the top rail runs straight and gaps between sections are even. Gates and any electrical or access elements are tested before the crew leaves.

Where safety guidance applies to railings or barriers, we refer to the Israeli railing standard SI 1142 in general terms, and exact dimensional checks are confirmed with your engineer.

Choosing the Right Partner for the Job

Look for a workshop that measures on site, provides a written specification, and explains which parts are reused and which are new. Since 1945 our factory on Rival Street in Tel Aviv has handled iron, aluminum and steel work to measure, and the same team that makes a fence can advise on moving it. Ask for photos and a clear step-by-step plan before you commit.

Frequently asked questions

Can all aluminum fences be moved and reinstalled?

Most can, as long as the panels are not badly bent or corroded and the posts are sound. An inspection on site tells you which parts are reusable.

Will the fence look the same after it is moved?

Yes, in most cases. Components are labeled during dismantling, damaged parts are repaired or replaced, and finishes are restored where needed.

Do I need to be home during the work?

It is helpful to be present for the site survey and final check. Coordinate access to the area so the crew can work safely.

Do you handle both iron and aluminum fences?

Yes. We manufacture and install both iron and aluminum fences, so the same workshop can dismantle, repair and reinstall either type.

Common mistakes to avoid

Owners often remove a fence without marking the panels, which makes reassembly slow and error-prone. Skipping a level check on the new line can also leave a fence visibly crooked.

Our recommendation

Photograph the fence and mark each section before anything is removed, and insist on a written drawing of the new line before work begins. This single step prevents most reinstallation problems.

Summary

Aluminum and iron fences can be carefully dismantled, inspected, repaired and reinstalled at a new position with proper measurement and finishing. Plan the new line first and work with a workshop that provides a written specification.

השאירו פרטים ונחזור אליכם