Booking a Gate Site Measurement: What to Expect at Your Yard

Why an On-Site Measurement Matters

Photos and rough dimensions are a good starting point, but they rarely show the full picture. A gate has to fit a real opening, clear the ground, swing without hitting a wall or a plant bed, and carry its own weight on a solid post. Measuring on site lets us see these details before we cut a single piece of steel or aluminum.

For homeowners, this visit is the moment to confirm what is possible in your yard. For building committees and contractors, it gives a written basis for the drawing that everyone approves.

How to Prepare Before We Arrive

A little preparation makes the visit faster and more useful. Clear the area around the opening so we can reach the posts and walls comfortably. Note whether you want a swing gate or a sliding gate, and which side you prefer for the opening direction.

• Take a few wide photos of the opening from both sides
• Mark the spot where you would like the gate posts to stand
• Note any existing electric connections or cables nearby
• Tell us if the ground slopes or if there is a drain or curb

What We Measure During the Visit

We record the clear width and height of the opening, the thickness of the walls or pillars, and the level of the ground on both sides. We also check how the gate will swing or slide, and whether there is room for an electric operator and its wiring.

Points we always check

We look at the condition of existing posts, the type of surface where anchors will go, and the space needed for maintenance. Where a gate will be fitted to a particular railing or fence line, we measure that as well so the finished work looks consistent.

From Measurement to Approved Drawing

After the visit, we prepare a drawing and a written specification that describe the gate's dimensions, materials, finish, and mounting method. We send these to you for review. Nothing goes into production until you have approved the drawing, so you know exactly what you are getting.

If anything on the drawing does not match your expectations, this is the easiest moment to adjust it, before work begins in the factory.

Booking Your Visit to Techno Kol Uzi

Our factory is at 37 Rival Street in Tel Aviv, and the team has been working with metal since 1945. To book a site visit, send us a few photos of the opening and tell us roughly where the yard is located and when you are free. We will confirm a time that suits you.

Homeowners, building committees, architects, and contractors are all welcome to request a visit, and we can plan one visit to cover several openings at the same property.

Keeping Your Gate Project on Track

Once the measurement is done, the rest of the process follows a clear order: approved drawing, production in the factory, finishing with hot-dip galvanizing or powder coating where needed, and then installation at your property. Good measurements at the start keep this sequence smooth.

If your schedule changes, let us know early so we can adjust the visit without delaying the rest of the project.

Frequently asked questions

Do I need to be home during the site measurement?

It is helpful if you or someone you trust can be there to show us the opening and answer questions about the area. We can also work with a contractor or architect acting on your behalf.

What if my yard has a slope?

Slopes are common and can usually be handled with the right gate design and mounting. Tell us about the slope when you book so we can plan for it during the measurement.

Can you measure more than one gate at the same property?

Yes, we can measure several openings in a single visit. This is efficient and gives us a complete picture for all the gates you plan to install.

What should I send before the visit?

Send a few clear photos of the opening from both sides, a rough description of what you want, and your preferred dates. This helps us prepare and makes the visit shorter.

Common mistakes to avoid

Booking a visit only after choosing a finished design is a common error, because the yard often decides the gate type. Skipping the measurement and relying on rough tape-measure numbers can lead to a gate that does not clear the ground or swing properly.

Our recommendation

Measure the clear opening and check the ground and walls before you choose a style, and let the site guide your decision. Ask for the written drawing to be approved before production starts.

Summary

A gate site measurement is a short on-site visit that confirms dimensions, ground conditions, and mounting points before manufacturing. Booking it early helps your gate fit correctly the first time.

Related guides

• Ordering a Custom Gate Sized to a Specific Opening
• Requesting a Gate Quote for a New Residential Driveway
• Swing Gate vs Sliding Gate: Which Suits Your Property Better
• Gates for Replacing a Damaged Old Entrance Gate
• What to Check Before Buying a Driveway Gate
• Choosing a Gate Height for Balancing Privacy and Views
• All models in this category