Custom Gate Order: Sized to Your Exact Opening

What a custom gate order actually involves

A custom gate is built around one specific opening, not picked from a catalog size. That means the order follows a clear path: you send an inquiry with photos, we measure the opening on site, we prepare a drawing and a written specification, you approve it, and only then does production begin in the factory.

Each step protects you from surprises. The measurement captures what photos cannot show, such as uneven ground, wall thickness and slope. The drawing lets you see the gate design, the opening direction and the finish before any metal is cut.

Measuring the opening correctly

Accurate measurement is the foundation of a good gate. We check the width and height at several points, because walls and pillars are rarely perfectly straight. We also note the ground level and any slope, since these affect the gap at the bottom and how the gate swings.

• Clear width between posts or walls
• Height from the ground to the top of the opening
• Floor slope and any obstacles nearby
• Space needed for the swing or sliding track

Choosing design, opening type and finish

Decide early whether you want a swing gate, a sliding gate or an automated electric parking gate. Each suits a different space. A swing gate needs clear room to open, while a sliding gate needs a flat track and space beside the opening.

Finishes matter too. Hot-dip galvanizing protects steel against weather, and powder coating gives a wide range of colors. Tell us where the gate will stand, whether near the sea or in a shaded yard, so we can recommend the right protection.

Reviewing the drawing and specification

Before production, you receive a drawing and a written specification. Read them carefully and check the dimensions, the design, the opening direction and the finish. This is the moment to ask for changes, because adjusting a drawing is far easier than correcting finished metal.

When everything matches what you want, give your written approval. The factory then starts production based on that approved version.

From factory to installation

Once approved, the gate is cut, welded and assembled in our factory at 37 Rival Street in Tel Aviv. The frame is then finished, whether galvanized, coated or both, so the surface resists rust and wear over time.

Installation follows, with the gate set on its posts or track and tested for smooth movement, correct alignment and proper latching. We check that it closes fully and sits level before handing it over.

Safety and standards to keep in mind

A gate should move easily, close securely and never pinch fingers or pets. Good hinges, sound posts and a well-set track all contribute to this. Where gates include railings or infill, the Israeli railing standard SI 1142 applies in general, but exact measurement values should always be confirmed with your engineer.

If the gate is electric, plan for the power source and safety sensors early in the process, so the installation is complete and reliable.

Frequently asked questions

How long does a custom gate order take?

Timing depends on the design, the finish and the current workload. We confirm the schedule once the drawing and specification are approved.

Do I need to be home for the measurement?

Yes, it helps to be present or to have someone available who knows the site. Being there lets us ask about the opening direction and any obstacles.

Can I change the design after approving the drawing?

Changes are best requested before approval. After approval, any modification may affect production, so we discuss it with you first.

Do you make gates for both homes and yards?

Yes, we make gates for private homes, yards, building entrances and parking areas, all built to measure for the specific opening.

Common mistakes to avoid

The most common mistake is measuring only once or relying on photos, which miss slopes and uneven walls. Approving a drawing without checking the opening direction and the finish also leads to costly corrections later.

Our recommendation

Measure the opening at three points for width and height, note the ground slope, and decide on the opening type before you order. Review the drawing carefully so the final gate fits your space and your daily use.

Summary

A custom gate order is built around your exact opening, with measurement, drawing, approval, factory production and professional installation. Careful measuring and a clear approved drawing lead to a gate that fits and lasts.

Related guides

• Swing Gate vs Sliding Gate: Which Suits Your Property Better
• Booking a Site Visit to Measure a Yard for a Gate
• What to Check Before Buying a Driveway Gate
• Requesting a Gate Quote for a New Residential Driveway
• Measuring Your Gate Opening Correctly Before Ordering
• Gates for Replacing a Damaged Old Entrance Gate
• All models in this category