Buy Powder Coated Aluminum Doors Made to Measure in Tel Aviv

t411-43

To buy powder coated aluminum doors, you order them made to your exact opening, then choose a powder coat color and finish that suits your facade. Techno Kol Uzi manufactures each door in its Tel Aviv workshop after measuring on site and approving a written specification with you.

Why choose powder coated aluminum for your door

Powder coated aluminum is a practical choice for entrance and balcony doors because aluminum does not rust, and the powder coat adds a durable, even color layer on top. It handles sun, rain and salt air well, which matters for homes near the coast and for doors that get daily use.

Compared with painted surfaces, a powder coat is applied as dry powder and cured with heat, giving a harder and more consistent finish. Maintenance is usually limited to occasional washing with mild soap and water.

Choosing the color and finish

Color is the first decision most buyers make. Consider the rest of your building: matching window frames, railings and gates keeps the facade looking coordinated. Ask to see color samples before you confirm, because screen colors can look different in daylight.

Gloss level: matte hides small marks, while glossy surfaces look sharper
Texture: smooth or fine-textured finishes suit different architectural styles
Consistency: order all metalwork in the same batch for matching shades

Made to measure, not off the shelf

Standard door sizes rarely fit older openings or unusual wall layouts. A made-to-measure door is sized to your actual frame, so you avoid gaps, awkward fillers and forced installation. Our team takes the measurements on site, checking the opening at more than one point because walls are seldom perfectly square.

The measured dimensions go into a drawing and written specification that you review and approve before production begins. Any changes at that stage cost far less than changes after the door is built.

How the ordering process works

Start with an inquiry and a few photos of the opening. We then arrange an on-site measurement and prepare a drawing with the materials, profile, glazing or panel details, opening direction and finish. You approve the specification, production takes place in our factory, and the door is finished and installed on site.

Inquiry with photos
On-site measurement
Drawing and written specification
Your approval
Factory production and finishing
Installation

Checking quality before installation

Before the door leaves the workshop, check the finish under good light for even color and any surface marks. Confirm that the hardware, locking points and glass or panel infill match what you approved. Check the frame for square and that the door swings freely in its opening.

For doors that serve as safety barriers or sit beside stairs and balconies, confirm the requirements with your engineer, including references to the Israeli railing standard SI 1142, since exact values depend on your specific project.

Caring for a powder coated aluminum door

Powder coated aluminum needs little upkeep. Wash the surface with lukewarm water and a mild, non-abrasive soap, rinse well, and dry with a soft cloth. Avoid harsh solvents, steel wool and abrasive powders, which can dull or scratch the finish over time.

Check the seals and hardware once or twice a year, and keep drainage paths clear so water does not collect at the bottom of the door.

Frequently asked questions

Can I order a powder coated aluminum door in a non-standard size?

Yes. Doors are made to measure, so the size follows your actual opening. We measure on site before production starts.

How do I choose the right color?

Look at the surrounding windows, railings and gates, and ask for color samples. Viewing samples in daylight helps you judge the shade accurately.

Does powder coated aluminum rust?

Aluminum itself does not rust, and the powder coat adds a protective layer that resists weather. Regular gentle cleaning keeps the finish looking good.

Do I approve the design before production?

Yes. You receive a drawing and written specification, and production begins only after you approve them.

Common mistakes to avoid

Ordering from a rough estimate of the opening instead of an on-site measurement often leads to gaps or forced fits. Choosing a color from a screen without checking a physical sample can also lead to disappointment.

Our recommendation

Measure the opening at several points and send photos with your inquiry, then compare color samples in daylight before approving the specification.

Summary

Made-to-measure powder coated aluminum doors fit your opening, resist weather and stay easy to maintain when the spec and color are confirmed early.

השאירו פרטים ונחזור אליכם