Custom Glass Balustrades for Commercial Lobbies and Atriums

t349-30

A commercial glass balustrade is a custom-made glass railing that protects open edges in lobbies, atriums and stairwells while keeping sightlines clear. Each one is measured on site, drawn to specification, fabricated in our factory and installed with fixings suited to the building's structure and traffic.

Why Glass Balustrades Suit Public Buildings

In lobbies and atriums, a glass balustrade does two jobs at once. It meets the safety requirement for open edges and drops, and it keeps the space feeling open and bright. Visitors can see across the floor, and natural light from above reaches the lower levels without interruption.

Glass also handles heavy public use well. It is easy to keep clean, and when the design is right it avoids the visual clutter of thick posts and rails. For facility managers, that means a space that looks cared for and stays easy to maintain.

Choosing the Glass and Fixing System

The glass type, thickness and edge treatment should be chosen for the actual load and the environment. Laminated safety glass is the usual choice for public areas, because if it breaks the pieces stay bonded to the interlayer.

Top-fixed, side-fixed or base-channel systems
Frameless or with a slim metal handrail
Clear, low-iron or tinted glass

The fixing system depends on what the slab or wall can carry. Our engineer checks structural details, and exact values are confirmed for each project.

From Survey to Installation

The process starts with an inquiry and photos. We then visit the site to measure every run, height change and corner, and note any obstacles such as floor finishes or ceiling features. The measurements feed into a written specification and drawing that you approve before anything is cut.

Once approved, the glass and metal parts are produced in our factory on Rival Street. Finishes such as powder coating or hot-dip galvanizing are applied where the design calls for them. Installation is planned to minimize disruption to a building that stays in use.

Safety and Standards

Balustrades in public buildings must meet the height, load and gap requirements that apply under Israeli standards, including SI 1142 for railings in general. Exact dimensional values depend on the location and use of each railing, so we confirm them with the project engineer rather than assume them.

Handrails, edge profiles and the spacing of fixings all affect how safe and comfortable a railing feels in daily use. Planning these details early avoids changes later in the project.

Design Options for Lobbies and Atriums

Commercial glass balustrades can follow straight, curved or stepped routes around a stairwell or open floor. Frameless glass gives the cleanest look, while a slim stainless steel or aluminum handrail adds grip and a finished edge.

Continuous runs that follow the building's lines
Corner and curved sections cut to measure
Coordinated metal finishes with entrance and stair details

We can match the balustrade to the interior designer's palette and the wider metalwork in the building.

Planning Your Project With Us

Facility managers and building committees usually come to us with a renovation or a new interior. Share your floor plans, photos of the space and any finish samples you already have. We will advise on glass type, fixings and handrail options before the on-site survey.

Clear communication at the specification stage keeps the project on track, especially where several contractors are involved. You approve every drawing, so there are no surprises at installation.

Frequently asked questions

What glass is used for commercial balustrades?

Laminated safety glass is the standard choice for public lobbies and atriums because it stays intact if broken. The exact thickness and build-up are chosen for each project's load and use.

Do you measure on site before making the balustrade?

Yes. We visit the site to measure every run, height change and corner before any drawing is made. The measurements are then confirmed in the written specification you approve.

Can the glass balustrade match our existing metalwork?

We can coordinate the handrail and fixing finishes with other metal elements in the building. Powder coating and hot-dip galvanizing are available where the design calls for them.

Who confirms the safety requirements for the railing?

Our project engineer checks the structural details and the applicable standards, including SI 1142 for railings. Exact dimensional values are confirmed for each project rather than assumed.

Common mistakes to avoid

The most common mistake is choosing the glass and fixing system before confirming what the slab or wall can carry. Measuring after the design is fixed also leads to costly changes.

Our recommendation

Involve the fabricator early, ideally before the interior design is locked, so the fixing system and handrail details are planned with the structure in mind. Ask for a written specification and drawing you can approve before production starts.

Summary

Custom glass balustrades give commercial lobbies and atriums safe, open edges that suit heavy public use. Measured on site, specified in writing and built in our Tel Aviv factory, they are fitted to the building.

השאירו פרטים ונחזור אליכם