Custom Steel Scaffold Towers Built for Your Work Site

t482-33

A custom steel scaffold tower is an elevated access structure fabricated to the exact height, footprint and load requirements of a particular job site rather than assembled from generic stock. Because it is built to measure, it can fit tight courtyards, uneven ground and unusual building geometry while keeping workers stable and safe.

Why Standard Scaffolding Does Not Always Fit

Many building sites have constraints that off-the-shelf scaffolding cannot easily handle. A narrow light shaft, a sloped courtyard, a facade with setbacks or a heritage wall with limited anchor points can all make a generic tower awkward or unsafe.

A custom steel tower starts from the actual conditions on site. Its height, width, platform levels and access points are set around the work, not the other way around. This matters most when the work is repeated over many floors or when the same access must serve several trades.

The Site Survey and Measurement Stage

Every custom job begins with an on-site measurement. We check the ground surface, the required working height, the clearances around the structure and where the tower can be tied to the building or anchored safely.

Working height and number of platform levels
Ground conditions and any slope or uneven surface
Access route for workers and materials
Nearby walls, balconies, cables and pedestrian areas

Photos sent in advance help us prepare, but the final drawing is always based on what we measure in person.

Design, Drawing and Written Specification

Once the measurements are confirmed, we prepare a drawing and a written specification showing the frame layout, bracing, platform positions, guardrails and toe boards. The specification states the intended use so that the structure is designed for the loads it will actually carry.

Exact structural values are verified with the responsible engineer. Guardrails and edge protection are planned in line with the Israeli railing standard SI 1142, and we confirm the final details before production starts.

Client Approval Before Production

We do not begin fabrication until the drawing and specification have been reviewed and approved by you. This step protects both sides: changes are cheap on paper and expensive once steel is cut and welded.

Please check the platform heights, access gate positions and any requirement from your building committee, architect or site supervisor. If something has changed on site since the survey, tell us before approval so the drawing can be updated.

Fabrication and Finishing in the Factory

The tower is cut, welded and assembled in our factory at 37 Rival Street, Tel Aviv, where we have worked in iron, aluminum and steel since 1945. Building the structure under controlled workshop conditions gives consistent weld quality and accurate dimensions.

For outdoor use, finishing matters. Hot-dip galvanizing and powder coating help the steel resist weather and corrosion, extending the life of the tower between projects.

Installation and Handover on Site

The completed tower is delivered and erected on site by our team, following the approved layout. Ground supports, base plates and tie points are checked before workers are allowed on the platforms.

Level and stable base confirmed before loading
Ties and anchors installed as specified
Guardrails and access points tested

Before handover, we walk through the structure with the site supervisor so everyone knows where access is and what the tower is rated for.

Frequently asked questions

How tall can a custom steel scaffold tower be?

Height depends on the base footprint, bracing, tie points and the loads planned for the platforms. We confirm the achievable height during the site survey and with the engineer before production.

Do you need drawings from the client?

No. We measure on site and prepare the drawing and specification ourselves, then ask you to approve them before fabrication begins.

Can the tower be moved to another site later?

Custom towers are often designed to be dismantled and reused, though the layout is specific to each job. Let us know if you plan to relocate it so we can design for that from the start.

Are the towers suitable for outdoor conditions?

Yes, when finished correctly. Hot-dip galvanizing or powder coating helps the steel handle weather, and we choose the finish based on how and where the tower will be used.

Common mistakes to avoid

Ordering a tower from photos alone, without an on-site measurement, often leads to wrong heights or blocked access. Skipping the approval of the drawing is another frequent error that causes costly changes later.

Our recommendation

Before ordering, walk the site with your supervisor and mark the access route, tie points and any obstacles, then send those notes with your photos. Clear information at the start makes the drawing faster and the tower safer.

Summary

A custom steel scaffold tower is designed around your actual site, measured on location, approved on paper and built in our Tel Aviv factory for safe elevated access.

השאירו פרטים ונחזור אליכם