Steel Conveyor Support Frames for Production Lines

t482-36

A steel conveyor support frame is the structure that holds a conveyor belt or roller line at the correct height, alignment and level along the production route. Custom frames are designed around your line length, load, layout and access needs, then fabricated and finished to fit your floor and equipment.

What a conveyor support frame does on your line

The support frame carries the conveyor bed, the rollers or belt and the products moving on them. Its job is to keep the line straight, level and at a steady working height, so material flows without jams, drifting or uneven wear on the drive components.

On a production floor, the frame also defines how workers reach the line, where guards sit and how maintenance crews get underneath for service. A well-planned frame makes these tasks simple from the start.

Information to gather before the first drawing

Clear inputs make the design faster and more accurate. Prepare the following before contacting us:

Total conveyor length and the route, including bends and inclines
Working height and the height of adjacent machines
Maximum load per meter and the typical weight of products
Product size, shape and how items are positioned on the belt
Floor condition and any existing anchor points or slabs

Photos of the area and a rough sketch with dimensions help us measure correctly on site.

Choosing the right steel and profile

Support frames are usually built from structural steel sections such as square or rectangular hollow profiles and angle iron. The section size depends on span length, the weight carried and the stiffness needed to prevent sag or vibration.

For food, pharmaceutical or wet environments, stainless steel may be more suitable than carbon steel. For most industrial lines, hot-dip galvanizing or powder coating gives good protection against wear and corrosion. We confirm the final material and finish together with you, based on the operating conditions.

Design details that prevent downtime

Good frame design considers how the line will be adjusted and maintained over years of use. Plan for adjustable feet to level the line on uneven floors, bracing to resist side forces, and mounting points for guards, sensors and drives.

Adjustable leveling feet with enough range for floor tolerances
Cross bracing at intervals suited to the load and span
Access openings and removable sections for belt replacement
Clear space for cable trays and service walkways

From drawing to installation

Our process starts with an inquiry and photos, followed by an on-site measurement. We then prepare a drawing and a written specification covering dimensions, materials, finishes and connection details. Once you approve the drawing, the frame is produced in our factory at 37 Rival Street, Tel Aviv.

After finishing, the frame is installed on your floor. Installation is planned around your production schedule so that the line returns to operation as quickly as possible.

Safety and compliance considerations

Conveyor structures must be safe for the people who work beside and below them. Edges should be finished, load paths should be clear, and guarding should protect against pinch points and falling items. Where handrails or access platforms are included, they should follow the relevant Israeli standard, SI 1142, and the exact dimensions should be checked with your engineer.

Frame loads, anchoring and any seismic or structural requirements for your building should be confirmed with a qualified structural engineer before installation.

Frequently asked questions

Can a steel conveyor support frame be built to fit an existing line?

Yes. We measure the existing equipment on site and design the frame to match its height, width and mounting points. This is often the simplest way to replace or extend a line.

What is the difference between carbon steel and stainless steel frames?

Carbon steel is strong and cost-effective for most dry industrial areas when properly finished. Stainless steel suits washdown, food or corrosive environments where hygiene and resistance to moisture matter most.

How do you level a conveyor on an uneven floor?

We design the frame with adjustable leveling feet and, where needed, base plates that can be shimmed. This allows the line to be set accurately even when the floor has small variations.

Do you install the frames as well as manufacture them?

Yes. After production and finishing, the frames are installed on site and aligned to the layout you approved. Installation timing can be planned around your production schedule.

Common mistakes to avoid

Ordering frames before confirming the final layout and load, or skipping adjustable feet, often leads to costly rework and misaligned belts. Measure the floor and equipment carefully before the design is approved.

Our recommendation

Share your line layout, product weights and future expansion plans at the inquiry stage, so the frame is designed with room to grow. Ask for the drawing and specification to be reviewed by your engineer before production starts.

Summary

Custom steel conveyor support frames keep your line aligned, level and safe, and they are built to match your layout and load. Plan the design with accurate measurements and clear requirements from the beginning.

השאירו פרטים ונחזור אליכם