Steel Hangar Frames for Small Aircraft and Vehicle Storage

What a Steel Hangar Frame Includes

A steel hangar frame is the load-bearing structure of a covered storage building. It typically consists of main portal or column-and-rafter frames, purlins that support the roof sheeting, bracing that keeps the structure stable against wind, and base connections that anchor it to the foundation.

For aircraft and vehicle storage, the frame must also leave a clear opening wide and tall enough for the item to enter and exit easily, with room for doors, tracks or lifting equipment.

Planning the Clear Span and Door Opening

The first decision is the clear span, the distance between supports with no columns in the way. For small aircraft, wingspan and tail height set the minimum opening, while vehicles need height for roof racks, lifts or antennas.

• Measure the largest item you will store, including tow bars and attachments.
• Allow working clearance on each side for handling.
• Consider future needs, since extending a frame later is harder than planning it now.

Materials and Protective Finishing

Hangar frames are commonly made from structural steel sections. Because they stand outdoors in changing weather, corrosion protection matters as much as strength. In our factory, we use hot-dip galvanizing for maximum protection of structural members and powder coating for a finished appearance and added resistance to sun and moisture.

Choosing the right finish for your coastal or inland location helps the structure keep its appearance and performance for years.

From Drawing to Installation

Every project starts with a site visit and measurement. We then prepare a drawing and a written specification so you can review exactly what will be built before production begins. Once you approve it, the frame is fabricated in our Tel Aviv factory, finished, and transported for installation.

Foundation preparation is coordinated with your contractor, and the structure is assembled on site with the anchoring details set out in the approved drawings.

Safety, Standards and Engineering Checks

A hangar frame must resist wind, its own weight and any snow or equipment loads expected at your location. Loads and member sizes are confirmed with the project engineer rather than assumed, and the design follows the applicable Israeli standards for steel structures and for railings and guarding where they are included.

Doors, bracing and anchor points should be checked as part of the approval stage so the finished building works safely in daily use.

Maintenance for Long Service Life

A well-built steel frame needs little attention, but a simple routine extends its life. Rinse off salt and dust in coastal areas, check bolts and connections periodically, and touch up any scratches in the coating promptly.

• Inspect door tracks and hinges every few months.
• Look for corrosion at the base where moisture collects.
• Keep drainage channels clear around the foundation.

Frequently asked questions

Can a steel hangar frame be built to a non-standard size?

Yes. Our frames are made to measure, so the width, height, length and door openings are designed around your actual space and items. We confirm all dimensions on site before production.

What information do you need to start a hangar frame project?

Send photos of the location, the approximate dimensions of the space, and the size of the aircraft or vehicles to be stored. We will then arrange an on-site measurement and prepare a drawing.

How is a steel hangar frame protected against rust?

Structural members are hot-dip galvanized and finished with powder coating. This combination provides strong protection against moisture, salt air and sunlight.

Do you handle installation as well as manufacturing?

Our process covers fabrication in the factory, finishing and delivery for installation. Foundation work is coordinated with your contractor, and assembly follows the approved drawings.

Common mistakes to avoid

Many owners measure only the item itself and forget door swing, handling space and future equipment, which leads to a frame that is too tight. Skipping the engineering review of wind and load requirements is another common and costly error.

Our recommendation

Measure the largest item with its attachments, add working clearance on every side, and request a written drawing and specification before approving production. Choose galvanizing plus powder coating if the location is near the coast.

Summary

A custom steel hangar frame gives small aircraft and vehicles reliable, weather-resistant shelter when it is sized correctly and finished for the site. Careful measurement, engineering review and proper corrosion protection are the keys to a long-lasting result.

Related guides

• Steel Frames for Bus Shelters and Public Waiting Areas
• Steel Frames for Boat Storage and Marine Equipment Covers
• Steel Structures for Playgrounds and Outdoor Recreation Areas
• Steel Livestock Pens and Feeding Structures for Farms
• Steel Sports Frames for Basketball Courts and Training Areas
• Steel Frames for Agricultural Greenhouses and Shade Houses
• All models in this category