Gate Repair Service Request for Private Homes

t269-20

A gate repair service request starts with a short description of the problem and a few photos sent to our workshop. We then measure the gate on site, identify the cause, and give you a written specification before any work begins.

Signs your gate needs professional repair

Some gate problems are easy to spot, while others build up slowly. A gate that drags on the ground, rubs against the post, or closes unevenly is usually telling you something about its frame, hinges or alignment.

Scraping or grinding when the gate moves
Sagging at the latch side or a gap that has grown
Rust bubbles or flaking paint on joints and welds
An electric gate that stops halfway or reverses without reason

If you notice any of these, it is better to act early, because small misalignments often become bent hinges and damaged posts.

What to prepare before you contact us

A clear request saves time for both sides. Take photos of the gate from the front and the side, and include the hinges, latch and the post it is attached to. A short video of the gate opening and closing can also help us understand the fault.

Note when the problem started, whether it happens in all weather, and if the gate is manual or electric. If you have an installation sheet or the name of the original manufacturer, keep it handy.

How the repair request process works

Our work follows a simple sequence. You send an inquiry with photos, and we arrange an on-site visit to measure the gate and examine the faulty parts. We do not guess from pictures alone.

After the measurement we prepare a drawing and a written specification describing the repair or replacement. Work starts only after you approve that specification. The repair is then carried out in our factory on Rival Street in Tel Aviv, finished, and installed back at your home.

Common causes of gate failure

Most gate problems come from a few recurring causes. Hinges wear out under weight, posts move when the ground shifts, and moisture leads to corrosion at welded joints. Electric gates add motors, sensors and limit switches that need periodic checking.

Worn or loose hinges
Frame distortion from heavy use or impact
Corrosion at joints and base plates
Misadjusted automatic limit settings

Repair or replacement: how we decide

Not every gate needs to be replaced. When the frame is sound, a repair such as new hinges, straightening, re-welding or re-finishing is often the better option. When the structure is badly corroded or deformed, a new gate made to measure may be more practical.

We explain both options in the written specification so you can compare them calmly. Final measurements, materials and safety checks are confirmed with the relevant engineer where needed, and the choice always stays with you.

Finishing and long-term care

A repaired gate should be protected again so the damage does not return. Depending on the metal and the use, we may use hot-dip galvanizing or powder coating to protect against rust and weather.

Simple care helps extend its life: wash the gate periodically, lubricate hinges and moving parts, check fasteners once or twice a year, and report any new noise or stiffness early.

Frequently asked questions

How do I start a gate repair service request?

Send us a short description of the problem along with clear photos of the gate, hinges and post. We will reply with the next steps and arrange an on-site measurement if needed.

Do you visit the home before repairing the gate?

Yes, we measure the gate and examine the faulty parts on site before preparing any specification. This ensures the repair is based on the actual condition of the gate.

Can you repair both manual and electric gates?

Our work covers the metal structure, hinges, latches and frames of both manual and electric gates. For the electrical or automation side, we check the mechanical part and coordinate with the relevant specialist where required.

Will I approve the work before it starts?

Yes. We send a drawing and written specification, and the work begins only after you approve it.

Common mistakes to avoid

Waiting until the gate jams completely and ignoring small changes such as scraping or sagging often turns a simple repair into a larger job. Trying to force a stuck gate can bend the frame and damage the posts.

Our recommendation

Check hinges, latch and the post every few months, and address any misalignment as soon as it appears. Keep clear photos of the gate in its good condition so any repair can be compared against the original.

Summary

A gate repair service request is simple: describe the problem, send photos, and let us measure and specify the work before anything is done. Early attention usually means a smaller and more affordable repair.

השאירו פרטים ונחזור אליכם