How to Measure Your Driveway for a Parking Barrier

t460-0

To measure your driveway for a parking barrier, record the usable width between the posts or walls, the length and slope where the barrier will sit, and the height and clearance needed for your vehicle. Take these measurements at the exact spot where the barrier will be mounted, then send them with photos so we can prepare a drawing and specification.

Why accurate measurement matters

A parking barrier only works well when it fits the space it was designed for. Small errors in width or height can mean a barrier that does not open fully, scrapes the ground, or leaves no room for a car to pass. Measuring carefully at the start saves time for everyone involved.

Because each driveway is different, we never rely on general dimensions. We use your actual measurements, taken at the point where the barrier will stand.

What to measure on your driveway

Gather these key figures before contacting us:

Clear width between the two side walls, posts or pillars
Length of the driveway section where the barrier will sit
Ground slope, measured from the street side to the house side
Height of the vehicle that will use the driveway
Available depth for the arm or gate to swing or travel

Write each figure in centimeters and note which point it refers to, such as the street-side opening.

Checking slope and ground conditions

The ground under the barrier affects how it is anchored and how level it sits. A noticeable slope, a dip, or uneven paving should be recorded. Note whether the surface is concrete, asphalt, or tiles, since this influences how the base is fixed.

Also mark where underground pipes, cables or drainage channels run. If you are unsure, let your contractor confirm this before installation so the mounting points are placed safely.

Planning clearance and mounting points

Clearance is the space a vehicle needs to pass above or beside the barrier when it is open or closed. Check that your car's roof, mirrors and bumper will not catch the arm. Mark on the ground where the posts or housing would sit, leaving room for the mechanism.

Exact structural values depend on the design and load, and they are checked with the engineer during drawing. Our role is to make sure your measurements are complete and clearly marked.

From your inquiry to a written specification

Once you send your measurements and photos, we review them and arrange an on-site visit if needed. We then prepare a drawing and a written specification covering dimensions, materials and finish. You review and approve it before any work begins.

This step confirms the details together, so production starts only when the plan matches your driveway.

Production, finishing and installation

Our factory at 37 Rival Street in Tel Aviv builds the barrier to your measurements. Components are finished by hot-dip galvanizing or powder coating to resist weather and daily use. Once the parts are ready, our team installs the barrier on site and checks that it opens, closes and clears the vehicle path properly.

We recommend a final test with the vehicle that will use the driveway most often.

Frequently asked questions

Do I need to measure the slope of my driveway?

Yes, slope affects how the barrier is anchored and how level it sits. Record the rise from the street side to the house side so the base can be planned correctly.

What photos should I send with my measurements?

Send a wide photo of the full driveway, a close-up of the mounting area, and one showing the walls or posts on each side. Photos help us confirm the measurements before the site visit.

Can I measure the driveway myself?

Yes, you can take the initial measurements yourself. We still recommend an on-site check, since small details like buried pipes or ground condition are easier to assess in person.

How long does the process take from inquiry to installation?

The timeline depends on the design and the production schedule. We confirm the timing with you once the specification and approval are complete.

Common mistakes to avoid

Measuring only the road width instead of the usable width at the barrier point is a common error. Forgetting to account for the vehicle's roof height and mirror width can also cause the barrier to clash with the car.

Our recommendation

Measure at the exact mounting location, not at the street edge, and mark the spot on the ground before measuring. Take each measurement twice and send it with clear photos to avoid revisions later.

Summary

Measure the usable width, length, slope, vehicle height and clearance at the exact mounting point, then send them with photos for a drawing and specification.

השאירו פרטים ונחזור אליכם