Laminated Glass Bank Teller Partitions: A Security Guide

t428-7

A laminated glass bank teller partition uses two or more glass layers bonded with a tough interlayer, so it resists impact and stays in place when cracked. It lets tellers and customers see and speak clearly while adding a practical barrier at the counter. Custom sizing, the right glass build-up, and a secure frame and fixing method are what make it work.

Why bank branches choose laminated glass at the teller station

A teller station has to balance two needs: staff safety and open communication with customers. Laminated glass answers both. When it is struck, the interlayer holds the broken pieces together, so the barrier does not shatter into the workspace. Because the glass stays clear, tellers can read documents, check identification and make eye contact without a speaking grille getting in the way.

Laminated glass also keeps daylight and sightlines open, which helps the branch feel welcoming rather than fortified.

Choosing the right glass build-up

The thickness and number of layers depend on the expected threat level, the size of the opening and the mounting method. Your security consultant or engineer should set the specification, and we build to that written spec.

Number of glass plies and interlayer type
Overall thickness and total weight of each panel
Whether the panel needs a sliding or fixed opening
Compatibility with a pass-through tray or speaking grille

Ask for the exact build-up in writing before approving the drawing.

Frame, fixings and the counter connection

A strong glass panel is only as good as the frame that holds it. The frame should be fixed into a solid substrate, not just the decorative counter top, and the joints must resist prying. We fabricate the frame in stainless steel or powder-coated steel to suit the branch finish.

Special attention goes to the junction between the partition and the counter, where gaps can be exploited. Sealing and fixing details should be drawn in the specification so the installer does not improvise on site.

Measuring and drawing for a bank installation

Every teller station is different, so the process starts with an on-site measurement. We check the counter height, floor finish, ceiling clearance and any electrical or data conduits that run through the area. The information goes into a drawing and a written specification that you approve before production.

Measuring carefully avoids the common problem of a panel that fits the drawing but not the room.

Compliance, coordination and handover

Bank branch work often involves several parties: the security consultant, the bank's facilities team, the general contractor and the architect. Clear coordination keeps the schedule and the specification aligned. We provide drawings and documentation that your team can share with each party, and we can coordinate timing so the installation fits the branch's operating hours.

Confirm any approval requirements with the bank's own procedures before work begins.

Practical checks before you sign off

Before the partition goes live, walk the installation with your facilities team. Check that the glass is clean and free of distortion, that the sliding or pass-through mechanism operates smoothly, and that the frame is firmly fixed with no movement at the counter line. Note the cleaning method, since laminated glass should be cleaned with non-abrasive products that will not damage the interlayer edges.

Frequently asked questions

What is laminated glass made of?

It is two or more layers of glass bonded together with a plastic interlayer. If the glass breaks, the interlayer keeps the fragments attached to the sheet.

Can a teller partition still be clear for customers to talk through?

Yes. Laminated glass stays transparent, and it can be combined with a speaking grille or pass-through tray as part of the design.

Do you install the partitions yourselves?

We manufacture the glass and frames to measure at our Tel Aviv factory; please ask us about the installation arrangement for your specific project.

How do I start a project with Techno Kol Uzi?

Send photos of the teller station and its approximate dimensions. We will arrange an on-site measurement and then prepare a drawing and written specification for your approval.

Common mistakes to avoid

Specifying glass without a written build-up from the security consultant is the most common error, as is leaving the counter junction unsealed. Both can leave the partition weaker than its rating suggests.

Our recommendation

Fix the frame into the structural base rather than the decorative counter, and approve the drawing and build-up in writing before production. Measure the real opening on site, not from older plans.

Summary

Laminated glass bank teller partitions protect staff while keeping communication open, but only when the build-up, frame and counter connection are specified correctly. Start with on-site measurement and a written specification.

השאירו פרטים ונחזור אליכם