Mezzanine Steel Staircase Design and Fabrication in Tel Aviv

t391-8

A mezzanine steel staircase is a custom-built steel stair that connects the floor to an upper platform inside a warehouse or workshop. It is designed around the available footprint, the floor-to-platform height, the expected load and the traffic it must carry. Built to measure in the factory, it gives a safe, durable and space-efficient access route.

Why steel suits a mezzanine staircase

Steel is a practical choice for a mezzanine because it carries heavy loads with slender members, which keeps the stair light in appearance and leaves more usable floor space below. It also handles the constant use typical of workshops and storage areas, where people and equipment pass through daily.

High strength for its weight
Consistent quality in the factory
Durable finishes for industrial conditions

Because the staircase is fabricated rather than assembled from stock parts, it can be shaped to the exact opening and height of your mezzanine.

Planning the layout and dimensions

Good planning starts with the space you actually have. We measure the floor-to-platform height, the opening in the mezzanine deck and the clear width needed at the bottom and top. The available footprint decides whether a straight run, a turning stair or a winder layout will fit without blocking aisles or doors.

Headroom, landing position and the direction the stair rises are all fixed during this stage, so the drawing reflects real conditions and not assumptions.

Design considerations for safety and comfort

A mezzanine stair should feel stable and predictable underfoot. Consistent step heights and depths matter more than anything else, since uneven steps are a common source of falls. The handrail and guarding must be designed together with the stair, and we check the requirements of the Israeli railing standard SI 1142 with the engineer, who confirms the exact values for your project.

Non-slip treads suited to the work environment
Handrails on both sides where traffic is heavy
Guarding at open edges of the platform

Fabrication in our Tel Aviv factory

Once the drawing and specification are approved, the stair is cut, welded and assembled in our workshop at Rival Street 37. Working in the factory allows accurate joints, clean welds and repeatable quality, and it means the stair arrives ready to fit rather than being shaped on site.

Components such as stringers, treads and supports are prepared to tolerance, then checked before they leave the workshop.

Finishing for industrial durability

A mezzanine stair in a warehouse faces dust, moisture, impact and frequent use, so the finish matters. Hot-dip galvanizing gives strong corrosion protection, and powder coating adds a durable colored layer. The right finish depends on the environment, and we will recommend one that suits how your space is used.

After finishing, each piece is inspected so that the coating is even and the surfaces are ready for installation.

Installation and what to expect

Installation is planned so the stair fits the opening and is fixed securely to the floor and the mezzanine structure. We confirm anchor points before fabrication where possible, which avoids surprises on the day. Plan for the stair to be in place with the mezzanine deck and handrails aligned and tested for movement.

Before use, check that the treads are firm, the handrail is secure and nothing obstructs the landing.

Frequently asked questions

How do I know what size staircase my mezzanine needs?

The size depends on the floor-to-platform height, the available footprint and the traffic the stair will carry. We measure on site and recommend a layout that fits your space safely.

Can a steel staircase be made to an unusual shape?

Yes. Because we fabricate to measure, straight, turning and winder layouts can all be made to suit an irregular opening or a tight corner.

Which finish is best for a workshop mezzanine stair?

Hot-dip galvanizing is a strong choice for corrosion protection, while powder coating adds color and a durable surface. The best option depends on the conditions in your workshop.

Do I need an engineer to approve the staircase?

For structural and safety values such as load and railing requirements, the project engineer should confirm the exact figures. We work with the engineer to make sure the design meets the relevant standards.

Common mistakes to avoid

Choosing a stair before measuring the real height and footprint often leads to a stair that is too steep, too narrow or blocks an aisle. Ignoring handrails and guarding until the end can also cause costly changes.

Our recommendation

Measure the floor-to-platform height carefully, decide the traffic you expect, and involve the fabricator and engineer early so the stair, handrail and mezzanine deck are designed together.

Summary

A custom steel mezzanine staircase, planned to your measurements and fabricated in our Tel Aviv factory, gives a safe and durable route to your upper level.

השאירו פרטים ונחזור אליכם