Order an Electric Gate Quote for Your Private House

What Affects the Quote for an Electric Gate

Every private house is different, so no two quotes look the same. The main factors are the width of the opening, the slope and surface of the driveway, the type of gate you prefer, and the finish you choose. Materials and the level of automation also change the scope of work.

• Clear opening width and height
• Ground conditions and slope
• Sliding or swing mechanism
• Infill design and material
• Finish: hot-dip galvanizing and powder coating

Knowing these points before you call helps us prepare a more precise proposal.

How to Prepare Your Inquiry

A good inquiry saves time for both sides. Take clear photos of the entrance from the street and from the inside of the property, and include the wall or pillars on each side. Note the approximate opening width and any obstacles such as trees, poles or a sloping curb.

If you already have an image of the gate style you like, attach it. Describe how often the gate will open, whether you need a pedestrian door alongside it, and whether you plan to add an intercom or remote control later.

On-Site Measurement and Drawing

After reviewing your photos, we arrange a visit to measure the opening and check the ground. We confirm the exact clearances, the position of the pillars and the space the gate needs when it opens or slides. Electrical access and cable routing are also noted at this stage.

Following the visit, we prepare a drawing and a written specification covering dimensions, the mechanism, materials, finish and installation steps. Exact structural values are checked with the engineer, so the drawing reflects the actual site conditions.

Choosing Between Sliding and Swing Gates

Sliding gates suit homes where the space in front of the entrance is limited, because they run along the fence line instead of swinging out. They are a common choice for driveways on slopes or near the street. Swing gates work well when there is room to open inward or outward and a more traditional look is preferred.

We will recommend the option that fits your plot, your daily use and the layout of your entrance, and explain the trade-offs clearly in the quote.

Approval, Production and Finishing

Once you approve the drawing and specification, production starts in our factory at Rival Street 37 in Tel Aviv. Each element is cut, welded and assembled to your measurements. The gate then receives hot-dip galvanizing and powder coating, which protect the steel against weather and salt air.

You will not be asked to sign off on anything you have not seen in writing, so the final result matches what was agreed.

Installation and Next Steps

Our team installs the gate, the motor and the controls at your property, then tests the safety sensors and the opening and closing cycle with you. We walk you through the remote controls and daily operation before we leave.

To begin, send us your photos and a short description of your entrance through the contact form or WhatsApp. We will reply with the next steps for the on-site visit.

Frequently asked questions

How long does it take to receive an electric gate quote?

Timing depends on the photos you send and the schedule for the on-site visit. Once we have measured the entrance, we prepare the drawing and written specification for your approval.

Do I need to be home for the measurement visit?

It is helpful if you or someone who knows the property can be present. We can then confirm access, clearances and the best position for the motor and cables.

Can you build a gate for a sloping driveway?

Yes, sloping driveways are common and can be handled with the right design. We check the ground during the visit and recommend the gate type and installation method that suit the slope.

Is a sliding gate or a swing gate better for a small plot?

A sliding gate is often the better choice for a small plot because it does not need space to swing open. We will confirm the best option after measuring your entrance.

Common mistakes to avoid

Many homeowners send only a single distant photo or forget to mention obstacles such as trees, poles or a steep curb. These details can change the design and installation method significantly.

Our recommendation

Measure the opening width yourself and note any ground slope before you request the quote, so the on-site visit can focus on confirming the details. Also decide early whether you want a pedestrian door, since it changes the layout.

Summary

Send clear photos and a short description of your entrance, then approve a written drawing and specification before production starts. Every electric gate is made to measure in our Tel Aviv factory.

Related guides

• Book a Penthouse Gate Consultation Appointment
• Request a Gate Survey for Your Apartment Building Entrance
• Schedule Installation of a Shared Building Gate System
• Gate Remote Not Working: Common Causes and Fixes
• Request an Office Gate Automation Proposal
• Troubleshooting a Swing Gate That Stops Mid-Travel
• All models in this category