Order Powder Coated Aluminum Partition Frames for Your Project

t425-46

To order powder coated partition frames, send your drawings, the glass thickness, the RAL or sample color you need, and the finish you prefer. Techno Kol Uzi makes aluminum frames to measure, coats them in the factory, and confirms a written specification before production starts.

Why Powder Coating Suits Aluminum Partition Frames

Powder coating is a dry finish applied electrostatically and then cured in an oven. It forms a durable, even layer that resists scratches and daily wear, which makes it a good choice for office partitions, showroom frames and glass vitrines that are touched and cleaned often.

Because the coating is applied as a powder, it can be produced in a wide range of colors and textures. For architects, this means the frame color can be matched precisely to the rest of the interior design rather than being limited to standard anodized shades.

Choosing Colors and Finishes

The most common way to specify color is by RAL code, which architects can read directly from the project palette. If you have a physical sample, bring it to the factory so the color can be compared under the same light.

Matte finishes hide fingerprints and suit modern interiors.
Gloss finishes reflect light and give a crisp, polished line.
Textured finishes add grip and conceal minor surface marks.

Ask for a sample panel when the color is critical, especially for large runs of partitions.

What to Send When You Place the Order

A clear inquiry saves time at every stage. Send your architectural drawings or sketches, the planned frame profile, the glass type and thickness, and the location in the building. Photos of the space help us understand how the partition will sit.

Also state the color reference, the quantity of units, and any fire or acoustic requirements that affect the glazing. The more complete the brief, the more accurate the written specification will be.

From Measurement to Finished Frame

Once the inquiry is received, we measure on site when needed, so that frames match the actual opening rather than the drawing alone. We then prepare a drawing and a written specification covering dimensions, profiles, glass fitting and finish.

After you approve the specification, the frames are cut, assembled and powder coated in our Tel Aviv factory at 37 Rival Street. Glass is fitted and the units are prepared for delivery and installation.

Coordinating Glass, Hardware and Installation

Partition frames work best when the glass, gaskets, hinges and fixings are planned together. Share the glass supplier details early so the rebate depth and glazing system are correct before coating begins.

Installation details such as wall fixings, floor channels and the sequence on site should be agreed with the contractor. Coordinating these points in advance reduces adjustments and protects the powder coating during handling.

Protecting the Finish on Site

Powder coated surfaces are durable, but they still need careful handling. Keep protective film in place until the final cleaning, avoid dragging frames over masonry, and use non-abrasive cleaners afterwards.

Check the frames on delivery against the approved drawing and color sample. Reporting any issue early makes it easier to resolve before the partitions are fully installed.

Frequently asked questions

Can I order a partition frame in a specific RAL color?

Yes. Send the RAL code or a physical sample, and we will confirm the color in the written specification before production.

Do I need to send drawings to order?

Drawings help, but photos and measurements are also accepted. We can measure on site to make sure the frames fit the actual opening.

Which finish is best for a busy office?

A matte or textured powder coat is usually practical because it hides fingerprints and small marks better than a high gloss finish.

Is the glass included in the partition order?

Glass can be fitted into the frames as part of the order. Tell us the glass type and thickness so the rebate and glazing are prepared correctly.

Common mistakes to avoid

A common error is approving a color from a screen image instead of a physical sample, since monitors vary widely. Another is ordering frames before the glass thickness and glazing system are confirmed.

Our recommendation

Request a sample of the exact RAL color and finish, and confirm glass specifications in writing before production begins. This small step prevents most color and fit issues on large partition projects.

Summary

Powder coated aluminum partition frames can be made to measure in your chosen color and finish, with the specification confirmed before production starts.

השאירו פרטים ונחזור אליכם