Ordering a Custom Metal Fence: Quote to Delivery

Step 1: Send an Inquiry With Photos

The process starts with a simple inquiry. Send photos of the area where the fence will stand, a short description of what you need, and any existing features such as walls, posts or gates. Mention whether the fence is for a private home, a building committee or a contractor project, since this affects the paperwork.

• Photos from several angles
• Rough dimensions if you have them
• Preferred material: iron or aluminum
• Style and any gate or automation wishes

A clear inquiry helps the team understand the project before anyone visits the site.

Step 2: On-Site Measurement

After reviewing the inquiry, a member of the team visits the site to measure. Accurate measurement is the most important step, because the fence is made to fit your exact space. The team checks the length of each run, the height, the slope of the ground, the position of posts and any obstacles.

Measure the site in advance if you can, but leave the final measurement to the professional visit. Small differences in ground level or wall alignment can change the dimensions of each panel.

Step 3: Drawing and Written Specification

Based on the measurements, a drawing is prepared showing the layout, panel sizes, gate positions and post locations. A written specification accompanies the drawing and lists the material, profile type, height, infill pattern and finish.

Read both documents carefully. Ask questions about anything unclear, such as how the gate swings or how the fence meets an existing wall. Safety requirements, including railing standards where relevant, are confirmed with the engineer before production.

Step 4: Client Approval and Production

Once you approve the drawing and specification in writing, the order moves to production at the factory on Rival Street in Tel Aviv. Components are cut, welded and assembled to the approved dimensions. Changing the design after approval can delay the schedule, so confirm everything before signing off.

Production is done in the workshop, which allows consistent quality and precise fitting of every panel and gate.

Step 5: Finishing

Metal fences are finished to protect them from weather. Iron fences are commonly hot-dip galvanized and then powder coated, which gives strong corrosion resistance and a choice of colors. Aluminum fences are usually powder coated.

• Hot-dip galvanizing for iron durability
• Powder coating for color and surface protection
• Checks before the fence leaves the factory

Ask which finish suits your location, especially if the fence faces the sea or a damp area.

Step 6: Delivery and Installation

The finished fence is transported and installed on site. Before installation, make sure the ground is ready, the posts or fixing points are prepared as agreed, and access for the team is clear. Electric gates and automation are commissioned after mounting so you can test their operation.

After installation, check the alignment, gate movement and finish together with the installer, and raise any issues while the team is still on site.

Frequently asked questions

How long does the whole process take?

The timeline depends on the size of the project, the complexity of the design and the production schedule. Your contact at the factory can give you an estimate once the drawing and specification are approved.

Do I need to be home during the measurement?

It helps to be present or to give clear access to the site. Being there lets you point out details such as gate position, slope and existing features.

Can I change the design after approving the drawing?

Changes are possible but may affect dimensions, cost and schedule, so they should be raised before production starts. Ask for an updated drawing for any change.

Is iron or aluminum better for a fence?

Iron offers strength and a traditional look, and aluminum is lighter with low maintenance. The right choice depends on the site, the desired appearance and how the fence will be used.

Common mistakes to avoid

Ordering before measuring carefully, or approving a drawing without checking gate swing and post positions, often leads to costly adjustments. Take time to review the specification before signing.

Our recommendation

Walk the site yourself before the visit, mark the exact fence line, and note any slopes or obstacles. Having this ready speeds up the measurement and reduces surprises at approval.

Summary

Ordering a custom metal fence follows a clear path: inquiry with photos, on-site measurement, drawing and specification, approval, factory production, finishing and installation. Careful preparation at each step gives the best result.

Related guides

• Lead Times for Custom Iron Fence Orders Explained
• Tolerances and Dimensional Accuracy in Fence Panels
• Site Survey Checklist Before Installing a Metal Fence
• Quality Checks During Iron Fence Production
• Checking Property Lines and Boundaries Before Fencing
• Surface Preparation Before Painting a Metal Fence
• All models in this category