Ordering a Replacement Part for an Existing Metal Door

t419-48

To order a replacement part for an existing metal door, send us clear photos of the door and the damaged part, along with any markings or model details you can find. We then measure on site and produce the part to match your door, so it fits correctly rather than being a generic substitute.

Identify the part you need

Before ordering, be clear about which component has failed. Common replacement items for iron and aluminum doors include locks and latches, hinges, handles, bottom rails, glass or panel inserts, and decorative infill sections. Knowing the exact part helps us understand whether it can be replaced on its own or whether the whole leaf needs attention.

Locks, latches and striker plates
Hinges and pivots
Handles and push bars
Panels, infill bars and glass inserts

If you are unsure, a clear close-up photo is usually enough for us to recognize the component.

Prepare photos and basic details

Good photos save time. Take one wide shot of the full door, one close-up of the damaged part, and one of any stamped or engraved marks on the frame or hardware. Note whether the door opens inward or outward, which side the hinges are on, and the approximate age of the door if you know it. This information lets us match the profile, finish and fixing points accurately.

Measurement on site

Dimensions are the most important factor in a replacement part. Our team can visit to measure the opening, the leaf and the existing part, checking width, height, thickness and hole positions. Measuring yourself is possible, but small differences of a few millimeters can prevent a part from seating properly, so an on-site check is strongly recommended for anything structural or load-bearing.

Drawing and written specification

After measurement, we prepare a drawing and a written specification describing material, profile, dimensions, finish and fixing details. You review and approve these before production starts. This step confirms that the part is exactly what you expect, and it gives you a clear record for your building committee or contractor if needed.

Production and finishing

Once approved, the part is manufactured in our factory at Rival Street 37, Tel Aviv. Iron components can be hot-dip galvanized and powder coated for long-term protection, while aluminum parts are finished to suit the existing door color. The finish is chosen to match your current door so the replacement blends in visually and resists weather.

Installation and follow-up

Installation is carried out by our team where possible, or we advise you on fitting if you prefer to have it done by your own contractor. We check alignment, operation of locks and hinges, and smooth movement of the leaf before we leave. If something does not sit right, we return to adjust it, since the goal is a door that works as it did originally.

Frequently asked questions

Can you replace just one part of my metal door?

In many cases yes. Locks, handles, hinges, and individual panels or infill sections can often be replaced without changing the whole door. We confirm this after reviewing photos and measuring on site.

Do I need the original manufacturer's part number?

It helps but is not required. If you can find any markings, we can use them, but photos and accurate measurements are usually enough to produce a matching part.

Will the new part match the color of my existing door?

We can match the finish during production, whether it is a galvanized, powder-coated or aluminum finish. Sending a photo in daylight helps us choose the closest match.

How do I start an order?

Send us photos of the door and the damaged part, plus your location and a short description of the problem. We will reply with next steps, including whether an on-site measurement is needed.

Common mistakes to avoid

Ordering a part based on a rough guess of size is the most common error, and it often leads to a piece that does not fit. Waiting until the door is badly damaged or insecure can also turn a simple replacement into a larger repair.

Our recommendation

Measure or have the part measured on site rather than relying on estimates, and keep a clear photo record of the door and its hardware. If the door is a security or entry door, replace damaged locking components promptly rather than postponing.

Summary

Ordering a replacement part for a metal door is straightforward when you provide clear photos and accurate measurements. We produce the part to match your existing door, finish it to suit, and install it so the door works properly again.

השאירו פרטים ונחזור אליכם