Ordering Custom Glass Vitrines as a Contractor: Step by Step

t423-13

A contractor orders custom glass vitrines by sending a short inquiry with photos and the project context, then arranging an on-site measurement. Techno Kol Uzi returns a drawing and written specification for approval before the glass and frames go into production and installation.

Why contractors order custom glass vitrines from a metalwork factory

Standard cabinets rarely fit the exact wall, ceiling height or design language of a client project. A custom glass vitrine or partition is built to the measured opening, with the frame profile, glass type and finish chosen to match the interior. For contractors, this means fewer site adjustments and a unit that fits the schedule of the other trades.

Working directly with a manufacturer also keeps the responsibility for dimensions clear. The factory measures, drafts and produces, so the contractor has one point of contact for the whole item rather than coordinating between a designer, a glazier and a carpenter.

Preparing your inquiry

A good inquiry saves time on both sides. Include photos of the space, the approximate opening or wall dimensions, the intended use of the vitrine or partition, and any design reference the architect or interior designer has provided.

Location in the project and the floor it belongs to
Preferred frame finish, such as stainless steel or a metal look
Whether the unit must be fixed or include doors
Any constraints from the building or other trades

Send everything in one message so the factory can plan the site visit.

On-site measurement and drawings

Measurement is the step that most affects fit. The factory's team visits the site, checks the actual wall, floor and ceiling conditions, and records dimensions at the point of installation. Walls are rarely perfectly square, so measuring on site is more reliable than working from plans alone.

After measurement, a drawing and a written specification are prepared. These cover overall dimensions, frame profiles, glass type and thickness, door arrangement and fixing method. The contractor and, where relevant, the architect review them before anything is produced.

Approval before production

The drawing is the reference for the whole job, so approval should be written and specific. Check the dimensions against the room, confirm the glass and finish, and make sure the fixing details suit the wall or floor construction. Any change requested after production starts can delay the project, so it is worth reviewing carefully at this stage.

What to confirm

All dimensions and the location of openings
Glass type and frame finish
Fixing method and any load requirements, checked with the engineer

Production and finishing

Once approved, the frames are cut, welded and assembled in the factory, and the glass is prepared to the drawing. Metal parts are finished for durability, with hot-dip galvanizing or powder coating used where the environment or the specification calls for it. Producing in the workshop means the unit arrives ready to fit rather than being assembled piece by piece on site.

Timing should be agreed at approval so the contractor can plan the installation around other trades.

Installation and handover

Installation is carried out once the wall, floor and surrounding finishes are ready. The contractor should confirm that the opening is clear, that services are routed where they are needed, and that the site is accessible for handling glass. Checking the unit on delivery and again after fixing helps catch any issue early.

At handover, the contractor receives the final drawing and the specification so the project documentation is complete.

Frequently asked questions

Can Techno Kol Uzi measure the site for a contractor?

Yes. The factory visits the site to measure the actual opening and conditions, since on-site measurement is the most reliable basis for a custom unit.

What do I receive before production starts?

You receive a drawing and a written specification covering dimensions, frame profile, glass type, finish and fixing method. Production begins only after you approve them.

Can the vitrine include doors or be a glass partition?

Yes. Custom vitrines can include doors, and glass partitions can be designed to the room. The arrangement is set out in the drawing for your review.

Who checks structural fixing requirements?

Exact fixing and load requirements are checked with the engineer on the project. The factory can prepare the details to suit the agreed construction.

Common mistakes to avoid

Ordering from a rough sketch without on-site measurement, and approving a drawing without checking dimensions against the room, are the most common causes of costly changes later.

Our recommendation

Send photos and measurements early, and review the drawing line by line against the room before approving. Clear approval at the drawing stage keeps production and installation on schedule.

Summary

Contractors order custom glass vitrines through inquiry, on-site measurement, drawing approval, production and installation, with each step confirmed in writing.

השאירו פרטים ונחזור אליכם