Replacing an Old Sliding Gate With a New Electric Motorized Model

t293-2

Replacing an old sliding gate with an electric model is worthwhile when the frame is corroded, the track is worn, or the manual gate is hard to operate. A new motorized gate is made to measure, installed on a new or refurbished track, and fitted with a motor, remote access and safety sensors.

When an Old Sliding Gate Should Be Replaced

Not every worn gate needs a full replacement, but some signs point clearly toward one. If the frame is rusted through at the welds, the gate sags so it no longer runs straight on its track, or the wheels and guide rollers keep failing, repairs will cost more over time than a new unit.

Visible rust or cracks at the bottom rail and corners
The gate jumps, binds or leans when opened
The original manual gate is too heavy for daily use
You want remote control, automation or better security

A short visit on site lets us judge whether the existing frame is worth keeping.

How the Replacement Process Works

We begin with an inquiry and photos of the current gate, then take exact measurements on site. The gate, track and motor are drawn to your opening and written up in a specification for your approval. Once you approve, the gate is produced in our factory on Rival Street in Tel Aviv, finished with hot-dip galvanizing and powder coating, and then installed at your property.

Removing the old gate and preparing the foundation for the new track is part of the installation, so the work is planned in advance.

Choosing the Right Electric Motor and Drive

An electric sliding gate needs a motor sized for its weight and length, and the drive must suit how often the gate is used. Busy driveways benefit from a heavier-duty motor and a rack-and-pinion drive, while lighter gates can use simpler systems.

We also consider power supply, the location of the control box, and whether you want a remote, keypad or intercom. Choosing these during the drawing stage avoids changes later.

Safety Features to Include

Motorized gates must stop safely when something is in their path. Good installations include photocell sensors across the opening, an obstacle-detection function that reverses the gate, and a clearly visible emergency release so the gate can be operated by hand during a power cut.

Safety also depends on the gate itself being stable, so the frame, rollers and track are checked before the motor is fitted.

Keeping the Old Track or Replacing It

Whether the existing track can be reused depends on its level, straightness and condition. If it is worn, bent or set unevenly, replacing the track is usually the more reliable option, because a new gate on a poor track will run badly and strain the motor.

We inspect the track during the site visit and explain what is needed, so you know exactly what the job includes.

What to Expect After Installation

After installation, the gate is tested for smooth travel, correct stopping points, sensor response and remote operation. We show you how to use the controls and how to operate the manual release. A new electric gate should move quietly and evenly, and any adjustment at this stage is part of the handover.

Simple routine checks, such as keeping the track clear of debris, help the gate run well for years.

Frequently asked questions

Can I keep my old gate and only add a motor?

Sometimes, if the frame is straight, sound and well-hung. We check the frame and track on site and tell you honestly whether it can take a motor safely.

How long does replacing a sliding gate take?

The time depends on the gate size, the track work and the finishing stage. We confirm the schedule with you after the specification is approved.

Will an electric gate still work during a power cut?

Yes, a properly installed gate includes an emergency release that lets you move it by hand. We show you how to use it during handover.

Do I need to measure the opening before ordering?

You can send photos to start, but we always take exact measurements on site before drawing the gate, so it fits your opening precisely.

Common mistakes to avoid

A common mistake is fitting a motor to a worn gate or uneven track, which strains the drive and shortens its life. Another is skipping safety sensors to save effort, which leaves people and vehicles at risk.

Our recommendation

Have the frame and track inspected before choosing a motor, and size the drive for how often the gate is used. Ask for a written specification that lists the motor, sensors and release mechanism before you approve the work.

Summary

Replacing an old sliding gate with an electric model is the right move when the frame or track is worn beyond practical repair. A proper site inspection, the right motor and full safety features make the new gate reliable for daily use.

השאירו פרטים ונחזור אליכם