Self-Build Owner's Guide to Ordering Steel-Look Windows

t437-39

Self-build owners can order Belgian steel-look profile windows and doors made to measure, using a clear process of inquiry, on-site measurement, drawings and written specification. Prepare your openings and photos early, approve the drawings carefully, and coordinate installation with your builder so the frames fit the wall correctly.

Why Steel-Look Windows Suit a Self-Build

Steel-look profile windows give a slim, industrial appearance with large glass areas, which many self-builders want for modern living spaces. The profiles are designed to look like traditional steel while offering the convenience of modern frames. Because each opening is different, made-to-measure production is the most practical route for a home built from scratch.

When you plan your house, think about the look you want from inside and outside, how much daylight each room needs, and how the windows will open. These choices shape the final order, so settle them before the drawings are prepared.

Preparing Your Openings and Photos

Start with a clear set of plans and note every window and door position. Photos of each opening, taken from inside and outside, help our team understand the surroundings before we visit. Mark the sill height, floor finish level and any items close to the opening such as shutters or service pipes.

Collect your architectural plans and elevations
List each opening by room and floor
Note the wall type and whether the masonry is finished

On-Site Measurement and Drawings

Measuring should happen when the openings are formed, and ideally after plastering if your wall finish affects the frame position. We measure each opening on site and check that walls are square and level. Accurate measurements prevent gaps and ensure the frames sit properly in the reveals.

After measuring, we prepare drawings and a written specification showing sizes, opening directions, glass types and finishes. Read these carefully and ask questions about anything that is unclear before you give approval.

Choosing Finishes, Glass and Hardware

Choose the colour, glass type and hardware for each window and door. Think about privacy, sound, heat and how you will clean the glass. For ground-floor openings or rooms facing the street, you may want additional security or privacy glass.

Consider the handles and locking points as well, since you will use them every day. Write your choices in the specification so there is no confusion during production.

Production, Finishing and Delivery Coordination

Once you approve the drawings and specification, the order goes into production at our factory at 37 Rival Street, Tel Aviv. Profiles are cut, assembled and finished according to the approved details. Protective coatings are applied to suit the conditions the windows will face.

Ask your builder when the shell will be ready for frames, so delivery and installation fit into the construction schedule. Good timing reduces storage problems and the risk of damage on site.

Installation and Checking Your Order

On installation day, check that each frame matches its drawing and that the openings are ready. Install the frames plumb and level, and make sure the sealing and fixings are completed as specified. Inspect each window and door for scratches, operation and hardware before the installer leaves.

Keep the drawings and specification with your project papers. If you need guidance on railings or safety-related items, exact requirements are checked with your engineer against the relevant standard.

Frequently asked questions

Can I order steel-look windows before my walls are finished?

Yes, but measurements should be taken when the openings are in their final form. If plaster or cladding will change the opening size, we recommend measuring after those finishes are complete.

What information do you need from me to start?

Send photos of each opening, your plans or sketches and the approximate sizes if you have them. We will then arrange an on-site measurement visit.

Do I approve the design before production starts?

Yes. You receive drawings and a written specification, and production begins only after your written approval.

Can the windows and doors be matched to a particular look?

Yes, the profiles can be matched to your design preferences, and we will confirm the finish and details in the specification before production.

Common mistakes to avoid

A common mistake is measuring before walls are finished or approving drawings without checking glass, opening direction and hardware. Both can lead to frames that do not fit or do not work as you expected.

Our recommendation

Confirm the opening sizes after plastering, and read the written specification line by line before you approve it. Ask your builder to plan the frame delivery for when the openings are ready and protected.

Summary

Ordering Belgian steel-look windows for a self-build works best with good photos, accurate on-site measurement, careful approval of drawings and a coordinated installation plan.

השאירו פרטים ונחזור אליכם