Stainless Steel Corner Guards for Hospital Corridors

t470-40

Stainless steel corner guards are fixed to the edges of hospital corridor walls to absorb impacts from gurneys, wheelchairs and carts. They are made to measure in the factory, finished for hygienic cleaning, and installed to protect plaster and paint at the points where damage is most frequent.

Why hospital corridors need corner protection

Hospital corridors see constant traffic from beds, medical carts, wheelchairs and equipment trolleys. Wall corners take the heaviest impacts, and plaster, paint and wall cladding often chip or crack there within months. Repainting corridors also disrupts patient areas and costs staff time.

A metal corner guard placed at the vulnerable edge absorbs these knocks and keeps the wall surface intact. Protecting the corner is usually far cheaper than repairing the wall over and over.

What to specify before ordering

Start by listing the corridor sections that see the most traffic, such as lift lobbies, turns near nurses' stations and doors to treatment rooms. Note the wall material, because the fixing method depends on whether the wall is block, concrete or a drywall system.

Height of the guard, typically reaching above the height of gurney handles
Leg or wing width and the thickness of the stainless sheet
Stainless steel grade suitable for a hospital cleaning regime
Finish, such as brushed satin for a discreet look
Length of each run and the number of corners to cover

Materials and finish for a clinical setting

Stainless steel is chosen in healthcare because it is strong, does not rust in normal use and can be wiped down with standard hospital disinfectants. A smooth, non-porous surface also avoids the build-up of dirt that can occur in rougher materials.

A brushed finish hides fingerprints and light scuffs better than a mirror finish, and it blends well with most corridor decor. The exact grade and thickness should be confirmed with your engineer against the requirements of your facility.

How the guards are made to measure

Each corner guard is cut, bent and finished in our workshop at 37 Rival Street in Tel Aviv, based on the measurements taken at your site. Because we manufacture to measure, the length, leg dimensions and fixing holes match your wall rather than a standard catalogue size.

Where a corner is not perfectly square or the wall is slightly uneven, we can adjust the profile so the guard sits flush. This avoids gaps that would collect dust.

Installation and fixing

Installation begins with a site visit to confirm measurements, mark the fixing points and check the wall condition. Guards are then fixed with suitable anchors so they remain secure under repeated knocks from heavy equipment.

Work is best scheduled in phases, corridor by corridor, so that routes stay open for patients and staff. We coordinate timing with your facility team to keep disruption to a minimum.

Maintenance and cleaning

Routine cleaning with mild detergent and a disinfectant approved for your facility is usually all that is needed. Avoid abrasive pads that can scratch a brushed finish and leave visible marks.

Wipe regularly with an approved disinfectant
Rinse where cleaners leave residue
Check fixings periodically, especially after heavy equipment has passed

Frequently asked questions

What height should hospital corner guards be?

The height is usually set so the guard covers the zone where gurneys, carts and wheelchairs make contact with the wall. Exact values should be checked with your engineer against the applicable Israeli standards.

Can stainless steel corner guards be cleaned with hospital disinfectant?

Yes, stainless steel is well suited to regular wiping with approved hospital disinfectants. Use soft cloths rather than abrasive pads to keep the finish looking good.

Can the guards be made for unusual corners or uneven walls?

Yes, because each guard is made to measure in our Tel Aviv workshop. We adjust the profile to suit the actual corner so it sits flush against the wall.

Can work be done without closing the whole corridor?

In most cases installation can be carried out section by section, so that routes remain open. We plan the work together with your facility team.

Common mistakes to avoid

Choosing guards by standard size instead of measuring the actual corner, and ignoring the wall type when selecting fixings, are the most common errors. Both lead to loose guards or gaps that collect dirt.

Our recommendation

Survey the corridor during a busy period to see where gurneys actually hit the walls, then specify guards for those exact points. A site measurement before ordering prevents costly rework.

Summary

Stainless steel corner guards protect hospital corridor walls from daily impacts and clean easily. Measured, fixed correctly and maintained with approved products, they remain effective for years.

השאירו פרטים ונחזור אליכם