Balcony Railing Planning: Choosing Height and Spacing

t320-1

Balcony railing height requirements are set by Israeli safety standards, and the exact values depend on your building and the height of the drop. Before ordering, confirm the required height and baluster spacing with your engineer, then have the railing measured on site so the design fits your balcony.

Why railing height and spacing matter

A balcony railing has two jobs: it keeps people from falling and it keeps small children from slipping through. Height deals with the first job and spacing deals with the second. Both are checked against the safety standard that applies to railings in Israel, commonly referred to as SI 1142.

The standard sets the requirements in general terms, and the exact numbers depend on factors such as the height of the drop and the use of the space. For that reason, we do not recommend choosing dimensions from a general article. Confirm the values with your engineer before production starts.

What to check before you measure

Before anyone measures, gather the information that will shape the design. Knowing these details early prevents changes later.

The height of the balcony floor above the ground or the level below
Whether the railing sits on the slab edge, on a wall or on a parapet
Whether children or pets use the balcony often
The style you want, such as steel bars, glass infill or a combination
Any building committee rules that apply to the facade

How we measure on site

Once you send photos and a short description, we arrange an on-site measurement. We record the total length of each run, the height from the floor to the top rail, the position of posts and fixing points, and any corners or steps.

We also check the condition of the slab or wall where the railing will be fixed. A clear measurement sheet is the basis for the drawing, so take a moment to confirm the numbers with us before approval.

Drawing, specification and client approval

After the measurement, we prepare a drawing and a written specification. The drawing shows the layout, the height, the baluster spacing and the fixing method. The specification lists the materials, profile sizes and finish.

Please review both documents carefully. Check that the height and spacing match the requirements your engineer confirmed. Once you approve in writing, production begins. Changes made after approval may affect the schedule, so it is worth settling details at this stage.

Production and finishing in our factory

Every railing is made to measure in our workshop on Rival Street in Tel Aviv. Steel sections are cut, welded and assembled to the approved drawing. Where the design calls for it, we apply hot-dip galvanizing for corrosion protection, followed by powder coating for colour and a durable surface.

Because the work is made to measure, the finished railing is checked against the drawing before it leaves the factory.

Installation and final check

Installation is the last step. The railing is fixed to the slab, wall or edge according to the approved method, and the posts, rails and infill are aligned and secured. We check the height and baluster spacing on site after fixing, so the finished balcony matches the drawing.

If anything on site differs from the measurement sheet, we tell you before continuing, so you can decide how to proceed together.

Frequently asked questions

What is the standard balcony railing height?

The required height depends on the standard and the situation, so there is no single value that fits every balcony. Ask your engineer to confirm the height for your specific balcony before ordering.

How close together should the balusters be?

Baluster spacing is set so that small children cannot pass through the gaps. Confirm the exact spacing with your engineer, since it depends on the design and the requirements that apply.

Do I need to measure the balcony myself?

You can take photos and rough dimensions to start the inquiry. We then carry out the on-site measurement, which gives the accurate figures needed for the drawing.

Can the railing height be changed after approval?

Changes are possible, but they affect the drawing and production schedule. Settle the height and spacing before you approve the specification to avoid revisions.

Common mistakes to avoid

The most common mistake is ordering a railing before confirming the height and spacing with an engineer. Another is approving a drawing without checking the dimensions against the actual balcony.

Our recommendation

Ask your engineer to write down the required height and baluster spacing, then give that note to us before the measurement. This keeps the design correct from the first drawing.

Summary

Balcony railing height and spacing are safety decisions, so confirm them with your engineer, measure accurately on site, and approve a clear drawing before production begins.

השאירו פרטים ונחזור אליכם