Cantilever Sliding Gate Manufacturing for Homes in Israel

t279-14

A cantilever sliding gate is supported only from one side by posts and rollers, so the leaf slides along a track without a bottom guide rail. This makes it a strong choice for homes with uneven or sloped ground, where a ground track would be hard to keep level. Each gate is manufactured to measure after an on-site survey of the opening and the terrain.

What a cantilever sliding gate is

A cantilever sliding gate carries its weight on a structure fixed to the side of the opening, usually a column and a carriage running on a top or lower rail. Because nothing sits in the ground along the path of the leaf, there is no channel to dig, flood or fill with debris.

The leaf is typically built from a steel frame with infill such as flat bars, mesh or solid panels, depending on how much privacy and wind resistance you need.

Why it suits uneven ground

Many yards in Israel are sloped, terraced or built on fill. A conventional ground-track gate needs a level channel, and any settling can make it bind or derail. A cantilever design avoids that problem because the gate does not depend on a continuous track beneath it.

Less excavation along the driveway
No bottom track to clog with sand or leaves
Easier adjustment if the surface moves slightly over time

How we manufacture it

Every cantilever gate starts with an on-site measurement of the opening, the slope, the posts and the clearance behind the gate when it opens. We then prepare a drawing and a written specification, which you approve before production begins.

In our factory we cut and weld the steel frame, fit the carriage and rollers, and add the infill. The finished gate is then hot-dip galvanized and powder coated for protection against weather, and it is delivered and installed on site.

Choosing the right size and design

The weight and length of the leaf determine the carriage and the post strength, so the design is always matched to your actual opening. Consider how the gate will be operated, whether manually or with an automatic motor, and how much visibility or privacy you want from the street.

Points to decide with us

Clear opening width and total leaf length
Infill style: bars, mesh or solid panel
Motorization and remote access
Finish colour and coating

Safety and installation checks

A sliding gate moves a heavy leaf close to people and vehicles, so guiding, stops and the movement path must be checked carefully. Where a pedestrian gate or railing is part of the same job, the Israeli railing standard SI 1142 applies in general terms, and exact dimensional values should be confirmed with your engineer.

After installation we check alignment, roller contact, the stop positions and the smooth travel of the leaf before handover.

Ordering from Techno Kol Uzi

Since 1945 our workshop at 37 Rival Street in Tel Aviv has made custom iron, aluminum and steel work, and today the third generation of the family continues that practice. You can start with an inquiry and a few photos of the opening and the slope.

From there we arrange the on-site measurement, send you the drawing and specification, and move to production once you approve the plan.

Frequently asked questions

Is a cantilever sliding gate better than a ground-track gate?

Not always, but it is often the better option on uneven or sloped ground because it does not need a level track. The right choice depends on the opening, the terrain and how the gate will be used.

Do I need to dig a channel for a cantilever gate?

Usually not along the path of the leaf, since the gate is supported from one side. Post foundations are still required, and we confirm the details during the on-site measurement.

How do you protect the steel from weather?

Our gates are hot-dip galvanized and then powder coated. This gives strong protection against rust in the outdoor conditions common in Israel.

Can the gate be automated later?

Yes, if the design is planned for it from the start. We can discuss motorization during the specification stage so the carriage and posts are suited to a motor.

Common mistakes to avoid

Ordering a gate without measuring the actual slope and clearance behind the opening often leads to binding or insufficient room for the leaf to open. Choosing a heavy infill without checking the post strength can also cause sagging over time.

Our recommendation

Measure the opening and the ground slope before ordering, and leave clear space behind the gate for the full travel. Send photos from several angles so the specification reflects the real site conditions.

Summary

Cantilever sliding gates suit homes with uneven ground because they do not rely on a level track, and each one is built to measure in our Tel Aviv workshop.

השאירו פרטים ונחזור אליכם