Double Swing Driveway Gates: Design and Fabrication

t279-12

Double swing driveway gates are two leaves that open inward or outward from a central meeting point, giving a wide, unobstructed vehicle entrance. Their design depends on the opening width, the gate weight, the swing space available and the operating method, whether manual or automatic. A properly fabricated pair is built from a rigid steel frame, hung on reinforced posts and finished to resist weather.

Why choose a double swing gate

A double swing gate is often the most practical choice when the vehicle opening is wide, typically more than a single leaf can comfortably cover. Each leaf carries half the span, which keeps individual panels lighter and easier to hang than one oversized gate.

The layout also suits driveways that open onto a yard or a courtyard with room for both leaves to swing. Homeowners often choose this style for its classic look, its clear full-width passage when open, and its flexibility for both pedestrian and vehicle use.

Wide openings without a heavy single panel
Balanced leaves that are easier to operate
Suitable for manual or automatic operation

Measuring the opening and the swing space

Accurate measurement comes before any drawing. We measure the clear width between the posts, the height from the ground to the top of the opening, and the level of the surface where the gate will swing. Slopes, steps and existing paving all affect how the leaves can move.

Swing space matters just as much as width. Both leaves need clear area in front of them to open fully, so we check obstacles such as parked cars, planters, walls and drainage channels. Where swing space is limited, we discuss alternatives with the client during the on-site visit.

Frame design and materials

The frame is the backbone of each leaf. We build it from steel sections sized for the leaf's width and weight, with internal bracing so the gate stays square over years of use. Infill can be flat bars, vertical bars, perforated sheet or a combination, depending on privacy and the look the client wants.

Aluminum or stainless steel parts are chosen where lightness or corrosion resistance is the priority. Every design is drawn and written up in a specification so the client can review exactly what will be built before production begins.

Hinges, posts and operation

Hinges and posts carry the full load of both leaves every time the gate moves, so they need to be strong and correctly aligned. We select heavy-duty hinges suited to the leaf weight and plan post foundations that resist movement. Posts should be plumb and firmly anchored before the leaves are hung.

Operation can be manual, with a bolt or latch system, or automatic with motors and controllers. Automatic systems need reliable power, safety sensors and clear spacing between the leaves and nearby objects. The choice is discussed with the client before the final specification is approved.

Fabrication and finishing

Fabrication takes place in our factory on Rival Street in Tel Aviv. Steel parts are cut, welded and checked against the drawing, then assembled into complete leaves so fit can be verified before anything leaves the workshop. This step catches small errors early and saves time on site.

For finishing, we use hot-dip galvanizing for corrosion protection, followed by powder coating in the color the client selects. This combination suits the coastal climate of central Israel and keeps the gate looking good for years with routine cleaning.

Installation and fit-up

Installation begins with setting and checking the posts, then hanging the leaves and adjusting them until they close evenly along the meeting edge. We check the gap at the top, bottom and center, confirm that both leaves latch securely, and test the full range of movement.

After installation we review operation with the client, explain maintenance such as lubricating hinges and checking fixings, and confirm that the gate is ready for daily use. Where a motor or safety device is included, it is commissioned and tested during this visit.

Frequently asked questions

How wide can a double swing gate be?

The practical width depends on the frame strength, the weight of the leaves and the posts supporting them. We size each leaf to the specific opening and confirm the design during the on-site measurement.

Should the gates open inward or outward?

The direction depends on the available space, the slope of the driveway and safety around the swing area. Inward swing is common when there is room inside the property, while outward swing may suit tighter plots.

Can a double swing gate be automated later?

Yes, if the posts, hinges and frame are planned for it from the start. We recommend discussing future automation during the design stage so the right fixings and wiring provisions are included.

How do you protect the gates from weather?

We hot-dip galvanize the steel frame and apply powder coating as a finish. This protects against corrosion and keeps the surface durable in the Israeli climate with routine maintenance.

Common mistakes to avoid

Many people measure only the opening and forget the swing space, which can leave leaves blocked by cars or walls. Choosing thin frames or weak hinges for a wide gate also leads to sagging and misalignment over time.

Our recommendation

Measure the clear opening, check the full swing arc on the ground, and decide on automation before the posts are set. Ask for a written drawing and specification so you can confirm the design before fabrication starts.

Summary

Double swing driveway gates offer a wide, practical entrance when they are measured carefully, built on a rigid frame and finished for outdoor conditions. A clear design and proper installation make the difference between a gate that works smoothly for years and one that does not.

השאירו פרטים ונחזור אליכם