How to Measure for a Custom Glass Partition: A Practical Guide

t433-29

To measure a glass partition, take the width and height of the opening at several points, since walls and floors are rarely perfectly straight. Use the smallest measurement as your reference, and record any obstacles, door swings and floor finishes before ordering.

Why Accurate Measurements Matter

A glass partition is made to fit one specific opening, so small errors can cause real problems at installation. A frame that is even a few millimeters off may not sit flush, may leave gaps, or may need rework that delays the project. Taking careful measurements before you order saves time for you and for the installation team.

Remember that a finished partition needs room for its frame, seals and fixings. Our workshop will calculate these allowances when we prepare the drawing, so your job is to record the actual opening as accurately as you can.

Tools You Will Need

You do not need professional equipment, but a few simple tools make the job much easier:

A steel measuring tape, preferably 5 meters or longer
A spirit level or a long straight edge
A pencil and a notebook or printed sketch sheet
A camera or phone for photos of each wall and corner

Use one unit throughout, such as millimeters or centimeters, and write it clearly on your sketch.

Measuring the Width

Measure the width of the opening at three points: near the floor, at the middle, and near the ceiling. Walls are often slightly out of square, so these readings may differ. Record all three numbers and mark the smallest one as your width reference.

Measure from wall face to wall face, and note whether the walls have plaster, tiles or other finishes, because these add thickness that affects the fit.

Measuring the Height

Measure the height on the left, center and right of the opening, from the finished floor to the finished ceiling. If the floor is tiled or will be tiled later, measure from the level you plan to finish at and note this on your sketch.

Also check for beams, pipes, ducts or lowered ceilings that might change the usable height. Photograph these areas so they are visible when we review your request.

Checking Depth, Obstacles and Door Swing

Measure the wall depth or thickness where the partition will sit, and note any recesses, skirting boards or electrical boxes. If a door is part of the partition, mark which way it opens and how much clearance is needed for the swing.

Note light switches, sockets and air vents near the opening
Mark any uneven floor areas or thresholds
Record the location of windows or doors that may affect the layout

Sending Your Measurements to Us

Once your measurements are done, send us a clear sketch with all dimensions and a few photos of the opening from the front and sides. Include the unit you used and the intended use of the space, such as a room divider, a shower area or a display unit.

Our team will review your information, come to site for an on-site measurement if needed, and prepare a drawing and written specification for your approval before production begins at our factory on Rival Street in Tel Aviv.

Frequently asked questions

Should I measure at more than one point?

Yes. Walls and floors are rarely perfectly straight, so measuring at three points across both width and height helps reveal any variation. Use the smallest reading as your reference.

Do I need to measure before or after the floor is finished?

Measure with the final floor level in mind. If tiling or flooring will be added later, tell us the planned finished level so the partition can be set correctly.

Can I order without a professional on-site measurement?

You can send your own measurements with photos to start the process. For the final order, we may still confirm the dimensions on site to ensure a precise fit.

What unit should I use when writing my measurements?

Use millimeters or centimeters and stay consistent throughout. Write the unit clearly on your sketch so there is no confusion when we review the drawing.

Common mistakes to avoid

The most common error is measuring only once in the middle of the opening and assuming the walls are straight. Forgetting to note floor finishes, door swing or obstacles can also lead to a partition that does not fit as planned.

Our recommendation

Measure twice, record three points for each dimension, and write everything on a labeled sketch with photos. This simple habit prevents most fitting issues before production begins.

Summary

Accurate measuring means checking width, height and depth at several points, noting obstacles and finishes, and sending clear sketches and photos. This gives your custom glass partition the best chance of a precise fit.

השאירו פרטים ונחזור אליכם