Measuring Your Opening for Custom Steel-Look Profile Windows

t447-20

To measure a window opening for custom steel-look profile windows, record the width and height at the top, middle and bottom, plus the depth of the wall, and use the smallest figures as your reference. Send these measurements with photos and the wall or frame condition, and the factory will confirm the final dimensions on site before production.

Why accurate measurement matters

A custom window is made to the exact size of your opening, so small errors cause real problems later. A window that is too large will not fit, and one that is too small leaves gaps that let in water, air and noise. Steel-look profile windows are precise products, which is why careful measuring at the start saves time and frustration for everyone involved.

Measure before you order, even if the old window looks straight. Openings in older buildings are often out of square, so one measurement is never enough.

Tools you will need

You do not need professional equipment, but a few basic tools make the job much more reliable:

A steel tape measure, preferably 5 meters long
A spirit level or a long straight edge
A pencil and a notebook or a phone for notes
A helper to hold the far end of the tape
A camera to photograph the opening from the front and the side

Measuring width and height

Measure the width at three points: the top, the middle and the bottom of the opening. Then measure the height at the left side, the middle and the right side. Write down all six figures, because a wall that is not perfectly straight will show different values.

Use the smallest width and the smallest height as your reference. This ensures the window will fit into the narrowest part of the opening. Measure from inside the wall face to inside the wall face, not from the old frame, since old frames can be damaged or misaligned.

Measuring depth and the wall reveal

Depth matters because it determines how the frame sits in the wall and how the window is fixed. Measure the thickness of the wall at the opening, and note whether the wall has a reveal, which is the recessed edge around the opening. Take the depth at more than one point if the surface is uneven.

Also note the material around the opening, such as concrete, block, stone or plaster. The fixing method depends on the wall type, and the factory will want to know this in advance.

Checking squareness and levelness

Use the spirit level to check whether the top and bottom edges of the opening are horizontal, and whether the sides are vertical. Measure both diagonals from corner to corner. If the two diagonal measurements differ, the opening is out of square.

Record any noticeable slope or bulge. You do not need to fix these problems yourself, but reporting them helps the fabricator plan the frame and confirm the correct installation method on site.

Sending your measurements and photos

Prepare a simple written list of your measurements, with the location of each figure marked on a sketch. Add clear photos of the opening from the front and from the side, and include a photo of the room inside so the position is easy to understand. Mention the intended use, such as a living room window or a balcony door.

Send this package to the factory. After reviewing it, the team will usually arrange an on-site measurement to confirm every figure before drawing and production begin.

Frequently asked questions

Should I measure inside or outside the opening?

Measure inside the wall opening from one finished wall face to the other, not from an old frame. This gives the true space the new window must fill.

How many measurements should I take?

Take at least three widths and three heights, plus two diagonals. Several readings reveal whether the opening is square and which figure to use.

Can I order using only my own measurements?

You can start with your measurements, but the factory normally confirms them on site before production. This protects you from small errors that are easy to miss.

What if my wall is not straight?

This is common in older buildings and is not a problem by itself. Note the variation in your measurements and photos, and the fabricator will plan the frame accordingly.

Common mistakes to avoid

The most common mistake is measuring only once and using the largest figure, which can make the window too big to fit. Another is measuring from the old frame instead of the wall opening.

Our recommendation

Take all your measurements twice, on different days if possible, and write the smallest values on your order sketch. When in doubt, let the factory confirm the dimensions on site.

Summary

Measure the width, height and depth at several points, check squareness with diagonals, and send clear photos with your figures. Accurate measurements lead to a custom window that fits well.

השאירו פרטים ונחזור אליכם