Railing Spec Approval: Confirm Stair Railings Before Production

t334-42

Railing spec approval is the step where you review and sign off on the measurements, drawings and written specification for your stair railings before production begins. Once you approve, we fabricate exactly what is on the paper, so checking details at this stage prevents costly changes later.

What Railing Spec Approval Means

Railing spec approval is the point where you confirm, in writing, what we are about to build. It covers the stair dimensions we measured on site, the drawing showing the railing layout, and the written specification listing materials, finish, heights and fixing method.

Approval is not a formality. It is the moment to catch anything that does not match what you expect, because after approval the railings go into production in our workshop at 37 Rival Street, Tel Aviv, and changes become harder and slower to make.

What We Check Before You Approve

Before sending your approval, go through the drawing and specification carefully. Make sure the following items are correct and match what you discussed with us:

Overall stair run, landing positions and turning points
Railing height and whether it is measured from the nosing
Baluster or infill type and spacing
Handrail profile, material and finish
Wall or floor fixing points and their positions
Any gaps that a child or a pet could pass through

If a detail is unclear, ask us before approving. A short question now saves a rework later.

Measurements and On-Site Verification

Our measurement visit is where the drawing starts. We record the actual stair geometry on site, because walls are rarely perfectly straight and finished floors can change the step height. The measurements on the drawing are the ones we will build to, so any difference between the plan and the real staircase should be resolved before approval.

If the stairs are still under construction, tell us. We can plan the fixing points against the structure, but we will need a final check once tiling and plastering are complete.

Safety Standards and Engineer Review

Stair railings in Israel should comply with the relevant national standard, including SI 1142 for railings. We design with the standard in mind, but exact values such as required height, load capacity and maximum opening size depend on your building and should be confirmed with your engineer or architect.

If your project is a building committee job or involves a permit, share the drawings with the engineer before approving. We can adjust the specification to match their requirements.

From Approval to Production and Installation

Once you sign the approved specification, we move to production in the factory. Steel parts are cut, welded and then finished, typically through hot-dip galvanizing or powder coating, depending on the chosen specification and the environment where the railing will stand.

After finishing, the railings are delivered and installed on site. Keeping the approved drawing as your reference makes the installation check straightforward for you and the installer.

Practical Tips for a Smooth Approval

A few habits make approval quick and accurate. Send photos of the staircase and any existing railing together with your inquiry. Keep one person responsible for decisions so that instructions do not conflict. Compare the drawing against the room, not only against memory.

Mark any change directly on the drawing
Confirm colour and finish with a physical sample when possible
Approve in writing, by email or WhatsApp, so there is a clear record

Frequently asked questions

Can I change the railing design after I approve the specification?

Changes after approval are possible but may delay production and add cost, since parts may already be cut or finished. That is why we recommend reviewing every detail carefully before signing.

Who checks that the railing height meets the standard?

We design with the relevant standard in mind, but your engineer or architect should confirm the exact values for your building. Share the drawing with them before you approve.

Do you measure again if the stairs are not finished yet?

If the stairs are still under construction, we can plan against the structure, but we will need a final measurement once tiling and plastering are complete to be sure of the fit.

How do I approve the specification?

Approve in writing, by email or WhatsApp, after reviewing the drawing and specification. A written approval gives both sides a clear record before production starts.

Common mistakes to avoid

The most common mistake is approving a drawing without checking the actual railing height and fixing points against the real staircase. Another is assuming that a verbal agreement covers finish colour and fixing details that were never written down.

Our recommendation

Walk the staircase with the drawing in hand and check each dimension against the room before you approve. If anything is unclear, ask for a revised drawing rather than approving and hoping for the best.

Summary

Railing spec approval is your final check on measurements, drawings and specifications before we build. Review carefully, confirm safety details with your engineer, and approve in writing.

השאירו פרטים ונחזור אליכם