Sliding Gate for a Self-Storage Facility Entrance

t286-23

A sliding gate for a self-storage facility is usually the best choice when the entrance has limited space to swing open and steady vehicle traffic. An electric unit with keypad, card or remote access lets tenants enter around the clock while keeping the site secured. Techno Kol Uzi designs and manufactures these gates to measure at its Tel Aviv factory after an on-site survey.

Why a sliding gate suits self-storage entrances

Self-storage sites often sit on narrow plots where a swing gate would block the road or the parking area when opened. A sliding gate runs along the fence line, so it uses only the length of the opening and nothing in front of it. This keeps the entrance clear for trucks loading cargo and for cars waiting behind a tenant.

Sliding gates also suit frequent use. Tenants come and go many times a day, and a well-built gate runs smoothly without the wind pressure problems that affect large swing leaves.

Planning the opening and the travel path

Before fabrication, the opening width and the clear space beside the gate must be measured on site. The gate leaf needs room to slide fully open with no obstacles, including planters, lamp posts, parked vehicles or slopes that could block the track.

Measure the clear opening and the free length on the sliding side.
Check whether the ground is level enough for a floor-mounted track.
Note slopes, drainage and existing utilities before digging.

Access control and tenant convenience

Most facility operators want a gate that opens for authorized tenants only. Electric operators can work with keypads, proximity cards, remote controls or phone-based access, and some sites add an intercom so staff can admit visitors. Plan the position of the access panel so drivers can reach it from the car without stopping in the road.

Consider also how the gate behaves during power cuts. A manual release lets staff move the leaf by hand, which matters for security and for tenants who need access at night.

Materials and finishing for a demanding site

A storage facility gate faces weather, dust and frequent movement. Steel frames finished with hot-dip galvanizing and a powder coat resist corrosion well in coastal and urban air. The infill can be solid sheet for privacy, or open bars for visibility and airflow, depending on what the operator wants to show the street.

Choose the infill and frame weight together with the motor size, since heavier leaves need stronger operators and firmer tracks.

Safety features and standards

Any powered gate should include safety sensors that stop or reverse the leaf if something is in its path. Pedestrian gates or a separate walk-through door are useful so staff and tenants can enter without opening the vehicle gate. Railings and barriers near the gate should meet the Israeli railing standard SI 1142 in general terms, and exact dimensions should be confirmed with the engineer on the project.

From inquiry to installation

The process usually starts with photos of the entrance and a short description of traffic and access needs. Techno Kol Uzi then carries out an on-site measurement and prepares a drawing and written specification for the operator to approve. Once approved, the gate is manufactured in the factory at Rival Street 37 in Tel Aviv, finished, and installed on site with the operator and access system set up and tested.

Frequently asked questions

Is a sliding gate better than a swing gate for a storage facility?

In most cases yes, when space in front of the entrance is limited. A sliding gate does not need clearance to swing, so it keeps the road and parking area free. Swing gates can still work on wide, open sites.

Can a sliding gate be automated with keypad or card access?

Yes. Electric sliding operators can be paired with keypads, proximity cards, remote controls and intercoms. The access method should be chosen with the operator's staff and tenant needs in mind.

What happens to the gate during a power cut?

A manual release allows the gate to be moved by hand. Battery backup can also be added so the gate keeps working for a limited time during outages.

How do I start a project with Techno Kol Uzi?

Send photos of the entrance and a short note on the opening size and traffic. The team will arrange an on-site measurement and then prepare a drawing and specification for your approval.

Common mistakes to avoid

The most common mistake is ordering a gate before measuring the free length beside the opening, which leaves the track blocked by a planter, pole or slope. Skipping safety sensors on an automated gate is the second costly error.

Our recommendation

Measure the travel path and ground conditions first, then choose the access system that matches how tenants actually arrive. Always include a manual release and a pedestrian entrance so the site stays usable when the power or the operator fails.

Summary

A sliding gate is a practical, space-saving and secure entrance solution for self-storage facilities when it is measured, designed and installed to the site's real conditions.

השאירו פרטים ונחזור אליכם