Cantilever Sliding Gate Fabrication for Tight Spaces

t293-33

A cantilever sliding gate is supported by a carriage and rollers at the top or on a raised beam, so nothing runs along the ground. It suits driveways where a standard track would be blocked by a curb, a drain, or a tight pavement edge. We fabricate these gates to measure after an on-site survey of your opening and the surrounding space.

What a cantilever sliding gate is

A cantilever sliding gate moves sideways like a standard sliding gate, but its weight is carried by a structure fixed to the wall or a post rather than by a bottom track. The leaf is held at one end and rolls along an overhead or raised guide, so the ground in front of the opening stays clear.

This makes it a practical choice when the entrance has little room on the ground, when the driveway slopes, or when a track would be easily damaged by vehicles or water. The gate still opens and closes electrically, with the same remote and access options you would expect from any parking gate.

When this design fits your property

Cantilever gates are worth considering in several common situations:

A concrete curb or raised pavement sits right at the gate line.
Drainage channels or utility covers would interfere with a ground track.
The driveway is narrow and the gate needs to slide into a wall space.
The surface is uneven and a bottom track would collect dirt and stones.

If your opening is wide or the leaf is heavy, the supporting structure matters more, so we check the span before recommending a design.

How we measure and design the gate

Every cantilever gate starts with an on-site measurement. We record the clear opening, the wall or post construction, the ground levels on both sides, and the space the leaf needs when it slides open. Photos of the entrance help us plan, but we always confirm dimensions on site.

After measuring, we prepare a drawing and a written specification covering the leaf size, the carriage and roller arrangement, the fixing points, and the finish. You review and approve the drawing before anything goes into production.

Fabrication and finishing in our factory

The gate is built in our workshop on Rival Street in Tel Aviv, where we cut, weld and assemble the steel frame to your exact drawing. The carriage and guide components are sized for the load and checked against the design before the leaf leaves the factory.

Steel parts are finished with hot-dip galvanizing for corrosion protection and powder coating for colour and appearance. Choosing the right finish for your exposure, especially near the coast, is part of the planning discussion.

Installation and safety considerations

Because the leaf is carried from one end, the fixing points must be solid. We plan the anchor positions with the wall or post structure in mind and confirm that the supporting element can carry the load before installation.

Safety features such as photocells, safe-edge sensors and proper stop limits are part of a complete installation. Where railings or guarding are involved, we follow the Israeli railing standard SI 1142 in general terms, and exact values are checked with your engineer.

Maintenance and long-term use

A cantilever gate needs less clearing than a ground track, since there is no channel to fill with debris. Still, the rollers, carriage bearings and fixings should be inspected periodically, and the coating should be checked for chips or wear where the leaf meets the ground or wall.

Keep the area around the support clear of vegetation and water, and have the motor and safety sensors serviced as part of regular checks.

Frequently asked questions

Is a cantilever sliding gate stronger than a standard sliding gate?

Strength depends on the leaf weight, the span and the fixing structure rather than the design type alone. A properly engineered cantilever gate is suitable for ordinary residential and parking use when it is sized for the opening.

Can a cantilever gate be installed on a sloping driveway?

Yes, a sloping driveway is one of the common reasons to choose this design, since no ground track has to follow the slope. We check the ground levels during the site measurement.

Do I need a clear area on the ground for a cantilever gate?

You need clear space for the leaf to slide open, but there is no track set into the ground. This keeps the pavement and drainage in front of the entrance undisturbed.

How do I start a project with your factory?

Send us photos of the entrance and a short description of your space. We then arrange an on-site measurement and prepare a drawing and specification for your approval.

Common mistakes to avoid

The most common mistake is measuring only the gate opening and forgetting the space the leaf needs to slide and the strength of the fixing point. Both should be checked on site before ordering.

Our recommendation

Measure the full sliding path, note any curb or drain edges, and confirm the wall or post can carry the load before choosing a cantilever design. Ask for a written drawing before production starts.

Summary

A cantilever sliding gate keeps the ground clear and suits tight or sloped entrances, and it is built to measure after an on-site survey.

השאירו פרטים ונחזור אליכם