Order Stainless Steel Handrails for Your Project

t362-40

To order stainless steel handrails, send us photos and basic details of your stairs or balcony, then we arrange an on-site measurement and prepare a written drawing and specification for your approval. Once approved, the handrails are manufactured to measure in our Tel Aviv factory, finished, and installed at your site.

Start with a clear inquiry

The first step is a simple inquiry. Send us photos of the staircase, balcony or area where the handrail will go, together with a short description of what you need: indoor or outdoor use, number of steps, wall or post mounting, and any preferred finish.

Photos from a few angles help us understand the site before we visit. If you already have an architect's plan or interior design drawing, include it as well, since it can speed up the process considerably.

On-site measurement

Once the inquiry is reviewed, our team measures the site in person. Exact measurements matter because stainless steel is cut and bent to fit, and small errors in length, angle or wall distance are hard to correct after production.

Total run length and height of each section
Wall, post or floor fixing points
Turns, landings and curved sections
Surface condition of the wall or floor

For railing heights and spacing, we follow the Israeli railing standard SI 1142 in general terms, and exact values are confirmed with your engineer.

Drawing and written specification

After measuring, we prepare a drawing and a written specification. These show the handrail profile, dimensions, joints, fixing method and finish, so you can see exactly what will be produced before anything is made.

Please read the drawing carefully and check the length, height, fixing positions and finish. Ask questions now, because changes are simplest before production begins.

Client approval

Production starts only after you approve the drawing and specification in writing. This step protects both sides: you know the final product, and we work from a confirmed design.

If you are working with a contractor, architect or building committee, we are happy to send the documents to them directly so that everyone signs off on the same version.

Manufacturing and finishing in our factory

Your handrails are cut, bent, welded and assembled at our factory at 37 Rival Street, Tel Aviv. Stainless steel work is done with careful attention to straightness, weld quality and joint alignment, so the finished rail looks clean and feels right in the hand.

Depending on the project and the material, the handrails may then receive a surface finish suited to their environment. We will confirm the finishing method in your specification before production.

Installation and handover

Our team installs the handrails at your site, fixing them to the wall, floor or posts as specified. We check alignment, height and fixing firmness before we leave, so the railing is ready for daily use.

Before installation, make sure the fixing surfaces are accessible and clear. If you have questions about the process or your project timing, contact us and we will walk you through each stage.

Frequently asked questions

What information should I send with my inquiry?

Send photos of the area, the type of handrail you need, whether it is for indoor or outdoor use, and any drawings you already have. The more detail you provide, the faster we can prepare an accurate proposal.

Do I need to be present for the measurement?

It helps to be present or to have someone who can give access to the site. We can also coordinate with your contractor or architect if you prefer.

Can I change the design after approving the drawing?

Changes are easiest before production starts, so please review the drawing carefully. Once manufacturing has begun, any change may affect timing and scope, and we will discuss it with you first.

Who checks the railing height and safety requirements?

We build according to your approved specification and follow the Israeli railing standard SI 1142 in general terms. Exact values should be confirmed with your engineer for your specific project.

Common mistakes to avoid

Ordering without accurate on-site measurements or skipping the written approval of the drawing are the most common causes of costly rework. Check length, height, fixing points and finish carefully before you sign off.

Our recommendation

Measure and confirm the fixing method early, especially for walls with tiles, cladding or uneven surfaces. Discuss the railing height and any safety requirements with your engineer before approving the final drawing.

Summary

Ordering stainless steel handrails is a clear process: inquiry, on-site measurement, drawing, approval, factory production and installation. Careful measurement and a confirmed specification lead to the best result.

השאירו פרטים ונחזור אליכם