How to Replace Vitrine Glass Panels in Existing Cabinets

t432-43

To replace vitrine glass panels, the existing cabinet frame is measured on site, a new panel is cut and finished to the exact dimensions and glass type you choose, and it is then fitted into the current frame. Keeping the original frame usually saves time and money compared with buying a whole new cabinet. Our team handles the measurement, production in our Tel Aviv factory and installation.

Start with an inquiry and photos

The first step is a short inquiry with clear photos of the vitrine, the damaged panel and the surrounding frame. Photos from a few angles help us understand how the glass sits, whether it slides in a channel, is held by clips, or is set in silicone. Tell us what you want to change: the glass type, the tint, or the thickness. Owners replacing cabinet glass often find that a single photo of the frame is enough to decide whether a replacement panel is practical.

On-site measurement

Glass is made to the exact size of the opening, so measuring correctly is the most important part of the job. We measure the clear opening, not the outer frame, and check that the sides are square. Older cabinets are often not perfectly straight, so we take several readings and note any irregularity. We also check the depth of the glass channel, because the new panel must sit correctly inside it with room for expansion.

Clear width and height at top, middle and bottom
Glass channel depth and edge condition
Type of fixing: clips, gasket or silicone

Drawing and written specification

After measuring, we prepare a drawing and a written specification showing the panel dimensions, glass thickness, edge finish and any hardware needed. This gives you a clear picture before anything is cut. Please check the drawing carefully and confirm the glass type you want, such as clear, tinted or safety glass. Once you approve the specification in writing, we move to production. Exact safety requirements and thickness values are checked with the engineer for your specific installation.

Production in our factory

Our factory at 37 Rival Street in Tel Aviv cuts the glass to your approved measurements and finishes the edges so they are smooth and safe to handle. Where the design requires it, we prepare the panel for the existing frame, including any cut-outs or sealing surfaces. Working to a confirmed drawing means the panel arrives ready to fit, which reduces adjustments on site and keeps the cabinet looking like it was built as one unit.

Installation into the existing frame

On installation day, we remove the damaged glass carefully, clean the channel and check its condition before fitting the new panel. The new glass is set into the channel with the correct gaskets, clips or sealant, leaving the small clearances needed for movement. We then test the door or sliding parts of the cabinet to make sure everything still runs smoothly. Clean-up is part of the job, so you are not left with glass dust or packaging around your home.

Final check and aftercare

Once the new panel is in place, we review the fit together, looking at alignment, sealing and how the glass sits in the frame. Handle the new panel gently in the first days, avoid knocking the edges, and clean it with a soft cloth and a mild, non-abrasive cleaner. If anything in the cabinet looks out of line after installation, contact us and we will check it promptly.

Frequently asked questions

Can I keep my old cabinet frame if only the glass is damaged?

In most cases yes. If the frame is sound and the glass channel is in good condition, only the panel needs replacing, which is usually simpler and more economical than a new cabinet.

Do you measure the glass on site?

Yes. We measure the actual opening on site, because the existing frame is rarely a perfect rectangle and accurate measurements prevent fitting problems.

Can I change the glass type when I replace the panel?

You can choose a different glass type, such as tinted or safety glass, as long as it suits the thickness and channel of the existing frame. We confirm this in the written specification before production.

Do I need to be home during installation?

It is helpful to be present to check the fit and confirm the result, but the main work is planned so you can see the finished panel and approve it.

Common mistakes to avoid

The most common mistake is measuring the outer frame instead of the clear glass opening, which leads to a panel that will not fit. Another is skipping the written specification and discovering the wrong glass type only after it is cut.

Our recommendation

Before ordering, measure the clear opening at three heights and widths, and send clear photos of the channel. Confirm glass type and thickness in writing so the panel is made to the right specification the first time.

Summary

Replacing vitrine glass panels is a measured, planned process: inquiry, accurate on-site measurement, approved drawing, factory production and careful installation into your existing frame.

השאירו פרטים ונחזור אליכם