Order Replacement Parts for Your Parking Barrier

t460-44

To buy parking barrier replacement parts, send us photos and the exact make, dimensions and mounting details of the barrier you have. We measure on site, prepare a drawing and written specification for your approval, then manufacture the components in our Tel Aviv factory and install them.

What information we need before you order

Spare parts for a parking barrier only work if they match the original geometry, so the first step is gathering information. Send clear photos of the barrier arm, the housing, the mounting base and any visible labels or nameplates. If you know the manufacturer and model, include them, even if you are not sure.

Overall arm length and profile size
Post or column height and base dimensions
Pivot and fixing hole positions
Condition of the damaged or missing part

Written notes help as much as photos, especially about how the barrier is used daily.

On-site measurement by our team

Once we review your inquiry, we arrange a visit to measure the barrier directly. Measuring on site avoids the common problem of parts that look right in a photo but do not fit the existing mounting. We check the alignment of the post, the clearance needed for the arm to swing fully, and the condition of the surrounding concrete or steel.

If the barrier has been modified in the past, we note those changes too, since they can affect how a replacement part must be made.

Drawing and written specification

After measuring, we prepare a drawing that shows the part with its dimensions, material and finish, together with a short written specification. The specification lists the material grade, the profile type, the connection method and any hardware included. You review both documents before anything goes into production.

This step protects you from surprises. If something in the drawing does not match what you expected, it is far easier to correct it now than after the part has been made.

Approval and production in our factory

Once you approve the drawing and specification in writing, the parts move to production at our workshop at 37 Rival Street, Tel Aviv. Our team cuts, welds and shapes the components to measure, working from the approved dimensions rather than estimates.

Cutting and shaping to the drawing
Welding and assembly of sub-parts
Fit check against your existing barrier where possible

Finishing: galvanizing and powder coating

Parking barriers stand outdoors and take constant wear, so finishing matters. Depending on the part and your site conditions, we use hot-dip galvanizing for steel corrosion protection, and powder coating for colour and an added protective layer. We agree on the finish during the specification stage so that the new parts match the existing barrier as closely as possible.

Finishing is done before installation, so the parts arrive ready to fit.

Installation and handover

The last step is installation at your site. We fit the replacement parts, check that the arm moves smoothly through its full travel, and confirm that the mounting is secure. If the barrier has electrical or automatic components, we coordinate the mechanical fit with the relevant specialist so that the whole system works together.

Before we finish, we walk through the result with you and answer any questions about care and future maintenance.

Frequently asked questions

Can you make a replacement part if I only have a photo of the barrier?

Photos are a good starting point, but we always measure on site before making anything. This ensures the part fits the actual mounting and clearance.

Do I need to know the barrier manufacturer and model?

It helps a lot if you do, but it is not essential. If you are unsure, send clear photos of the labels and the parts, and we will work out what is needed.

How do I approve the work before production starts?

We send you a drawing and written specification with dimensions, material and finish. Production begins only after you approve them in writing.

Are the parts galvanized or coated?

Steel parts can be hot-dip galvanized or powder coated, depending on the part and your site conditions. We agree on the finish during the specification stage.

Common mistakes to avoid

The most common mistake is ordering a part from a photo alone without measuring the mounting and swing clearance. Skipping the approval of the drawing is the second, since small dimension errors are much cheaper to fix before production than after installation.

Our recommendation

Measure the mounting holes and the arm's full swing path before you contact us, and write down the barrier's make if it is visible on the housing. Having these details ready speeds up the drawing stage considerably.

Summary

Ordering parking barrier replacement parts from Techno Kol Uzi follows a clear path: information, on-site measurement, approved drawing, factory production, finishing and installation. Following these steps keeps the new parts accurate and the barrier working reliably.

השאירו פרטים ונחזור אליכם