Reserve a Production Slot for Bulk Stainless Steel Panel Orders

t474-42

To reserve a production slot for bulk stainless steel panel orders, send us your project details and photos, then book an on-site measurement so we can prepare drawings and a written specification. Once you approve the specification, we schedule the batch into our Tel Aviv workshop and coordinate finishing and installation with your site timeline.

Why bulk stainless panel orders need planning

Large batches of stainless steel panels take up real workshop time, from cutting and forming to finishing and checking. When several floors, a façade or a building committee project are involved, the order has to fit into a schedule that matches your site work. Booking a production slot early helps contractors avoid waiting on material and crew when the site is ready.

A planned slot also lets us group similar panel types together, which keeps the work consistent across the whole batch.

Step 1: Send your inquiry with photos

Start by sending us a short description of the project and clear photos of the location. Include the number of panels, the approximate sizes if you have them, the building type and the expected installation window. Photos of existing railings, walls or cladding help us understand the conditions before we visit.

Project address and floor or elevation
Quantity of panels and any repeating sizes
Target installation date

Step 2: On-site measurement and drawings

After reviewing your inquiry, our team visits the site to take measurements. Panels are measured where they will be fixed, not only from plans, because walls and floors are rarely perfectly straight. Based on these measurements we prepare drawings and a written specification covering dimensions, panel layout, fixing points and finish.

Please check the drawings carefully. Any change at this stage is far simpler than a change after production starts.

Step 3: Approval and slot booking

Once you approve the drawings and specification in writing, we reserve the production slot for your batch. The approved document becomes the reference for the whole job, so confirm quantities, finish type and any special details before signing off. Your slot is then fixed in the workshop schedule.

If your timeline shifts, let us know as early as possible so we can adjust the booking.

Step 4: Production and finishing

During production, the stainless steel panels are cut, shaped and assembled in our factory at 37 Rival Street, Tel Aviv. Each panel is checked against the approved drawings before it leaves the workshop. Finishing is carried out as specified, and we handle the surface so the panels are ready for the site.

Panels are packed and labelled by installation area to make delivery and fixing easier on site.

Step 5: Installation and site coordination

We coordinate delivery and installation with your site schedule. Fixing methods are agreed in advance, and any structural questions are checked with your engineer. Exact load, fixing and railing requirements follow the relevant Israeli standards, including SI 1142 where it applies, and the engineer confirms the final values for your project.

Protect installed panels from construction dust and tools until handover.

Step 6: Handover and follow-up

After installation we walk through the completed work with you or your site representative and note any points that need attention. Keeping the approved drawings and specification on file makes it easy to add panels later in the same style. Contractors often book a follow-up batch once the first one is finished.

Frequently asked questions

How far ahead should I reserve a production slot?

Reserve as early as you can once the project scope is known, especially for large batches. Share your expected installation window so we can plan the slot around it.

Do you measure on site before production?

Yes. We measure at the installation location before preparing the final drawings, because actual wall and floor conditions often differ from the plans.

Can I change the design after approval?

Changes are possible but may affect the schedule, so they should be raised before production starts. Any agreed change is recorded in an updated specification.

Do you install the panels as well?

Yes, installation is part of our process and is coordinated with your site timeline. We agree fixing methods and details with you and your engineer in advance.

Common mistakes to avoid

A common mistake is approving drawings from plans alone without a site measurement, which can lead to panels that do not fit. Another is delaying the slot booking until the site is ready, when the workshop schedule may already be full.

Our recommendation

Send photos and a rough quantity early, book the on-site measurement, and approve a written specification before booking the slot. This sequence gives the most reliable timeline for bulk stainless panel batches.

Summary

Reserving a production slot works best with early inquiry, accurate on-site measurement, written approval and coordinated installation. Planning ahead keeps bulk stainless panel batches on schedule.

השאירו פרטים ונחזור אליכם