Frameless Glass Shopfront Manufacturing for Retail Spaces

t503-15

A frameless glass shopfront uses large sheets of toughened glass with minimal visible metal, so the store interior stays open to the street. It is built to measure from a detailed specification, with the glass, fixings and door hardware planned together before production starts. Techno Kol Uzi manufactures these shopfronts at its Tel Aviv workshop for designers and architects.

Why retail designers choose frameless glass

A frameless glass shopfront lets the product display and the interior light read clearly from the street. Visually, the glass becomes part of the brand rather than a frame around it. Large unbroken panels also make a small shop feel more generous than its actual footage.

Maximum visibility of window displays
Clean, contemporary appearance
Natural light deep into the space

Planning the design and the glass package

Early decisions shape everything that follows. Consider the glass thickness, whether the panels are single or laminated, the tint or coating, and where the door and its closer sit. Each glass panel is limited by its size and weight, so the opening widths and the number of panels should be agreed before the drawings are finalized.

Discuss with the engineer how the glass will be restrained and how wind and impact loads are handled. Exact structural values are confirmed with the engineer for each project.

Measuring on site

Accurate measurement is the foundation of a good shopfront. Our team visits the site to check the opening, the floor level, the ceiling line and any existing fixings. Walls are rarely perfectly square, so measurements are taken at several points and compared.

Photos taken before the visit help us prepare, but they do not replace on-site dimensions. Share any drawings from your architect so we can reconcile them with the real opening.

Fixings, patch fittings and hardware

In a frameless system the connections do most of the work. Patch fittings, point-fixed brackets and concealed channels hold the glass and transfer the load into the structure. Hardware such as door pivots, handles and locks must be chosen to suit the glass weight and the expected use.

Top and bottom patch fittings
Glass-to-glass corner connections
Concealed door closers and pivots

From drawing to factory production

After measurement we prepare a drawing and a written specification covering dimensions, glass type, fittings and finish. The client approves these documents before anything is ordered. Production then takes place in our factory, where metal components are cut, drilled and finished, and the glass is prepared for installation.

Working from an approved specification keeps changes to a minimum and helps the installation go smoothly on site.

Installation and handover

Installation requires careful handling because glass is heavy and fragile. The frames, channels and fittings are set level and plumb, then the panels are lifted in and secured. Final adjustment of the door and hardware is done once the glass is fixed, and the sealants and gaps are checked before handover.

We recommend that the architect or designer inspects the completed shopfront against the approved drawing.

Frequently asked questions

Is a frameless glass shopfront suitable for any store?

Most retail frontages can accommodate a frameless design, but the opening size, wall structure and local conditions decide what is practical. An on-site assessment confirms whether the chosen layout works.

Do I need to choose the glass before measuring?

Not always, but it helps to know the intended glass type early because it affects weight and fixings. We can advise on suitable options during the planning stage.

How is the door made to work with the glass panels?

The door is planned as part of the system, with concealed pivots or closers and matching patch fittings. Its weight and swing are calculated so it operates smoothly with the surrounding glass.

Who should I contact first when planning a shopfront?

Send your inquiry with photos and any existing drawings, and we will arrange an on-site measurement. Coordinating with your architect from the start makes the process simpler.

Common mistakes to avoid

A common mistake is fixing the opening dimensions before the glass and hardware are chosen, which can force costly changes later. Another is skipping coordination with the structural engineer on how the glass will be restrained.

Our recommendation

Agree the glass type, fittings and door layout together at the design stage, and confirm all dimensions on site before drawings are approved. Treat the specification as the single reference for production and installation.

Summary

Frameless glass shopfronts open a retail space to the street, and their success depends on careful planning, accurate measurement and well-chosen fittings. Techno Kol Uzi produces them to measure in Tel Aviv for architects and designers.

השאירו פרטים ונחזור אליכם